Manual Stiga TORNADO 2098 (page 63 of 112) (English, German, Dutch, French, Italian)

608469

Zoom out

Zoom in

1/112

4.3 KEY IGNITION SWITCH (Fig. 4.1 no.3)

«OFF» everything is switched o;

«HEADLIGHTS ON» (if tted);

«ON» activates all parts;

«START» engages the starter motor.

– On being released at the «START» position,

the key will automatically return to «ON».

– After turning the engine on, turn the lights on

(if tted) by turning the key to the «HEAD-

LIGHTS ON» position.

– To switch them o, turn the key to «ON».

4.4 PARKING BRAKE (Fig. 4.1 no.4)

This lever stops the machine from moving when

it has been parked. There are two positions:

«A» = Brake disengaged

«B» = Brake engaged

– The brake is applied by pressing the pedal

right down (4.21 or 4.31) and moving the lever

to position “B”. When you take your foot o

the pedal it will be blocked by the lever in the

lowered position.

– To disengage the parking brake, press the

pedal (4.21 or 4.31). The lever will return to

position «A».

4.5 CUTTING MEANS ENGAGE AND

BRAKE CONTROLS (Fig. 4.1 no.5)

The mushroom switch allows you to engage the

cutting means using the electromagnetic clutch:

«A» Pressed = Cutting means

disengaged

«B» Pulled = Cutting means engaged

– If you engage the cutting means without tak-

ing the necessary safety precautions, the

engine shuts down and cannot be restarted

(see 5.2).

– In disengaging the cutting means (Pos. «A»),

a brake is simultaneously activated which

stops their rotation within a few seconds.

4.6 CUTTING HEIGHT ADJUSTMENT

LEVER (Fig. 4.1 no.6)

There are seven positions for this lever, shown

as «1» to «7» on the label, which correspond to

various heights between 3 and 8 cm.

To go from one position to another, move the

lever sideways and put it back in one of the stop

notches.

4.7 REVERSE GEAR CUTTING CONSENT

BUTTON (Fig. 4.1 no.7)

By pressing and holding this button, it is pos-

sible to switch to reverse gear with the cutting

means engaged without causing the engine to

stop.

Mechanical transmission

4.21 CLUTCH / BRAKE PEDAL

(Fig. 4.2 no.21)

This pedal has two functions: during the rst

part of its travel it acts as a clutch, engaging

and disengaging drive to the wheels, and in

the second part it acts as a brake on the rear

wheels

IMPORTANT Do not keep the pedal half

way between clutch engagement or disen-

gagement, as this can cause overheating and

damage the transmission belt.

NOTE When the machine is in movement,

keep your foot off the pedal.

4.22 SPEED CHANGE LEVER

(Fig. 4.2 no.22)

This lever has seven positions for the 5 for-

ward speeds, the neutral position «N», and

reverse «R».

To go from one speed to another, press the

pedal (4.21) halfway and shift the lever as

shown on the label.

WARNING! Reverse must be en-

gaged when the machine has stopped.

Hydrostatic transmission

4.31 BRAKE PEDAL (Fig. 4.3 no.31)

This pedal works the brake on the rear

wheels.

4.32 CLUTCH PEDAL (Fig. 4.3 no.32)

This pedal engages drive in the wheels and

controls the machine’s forward and reverse

speed.

dimenzije pogonskih jermenov za stigo tornado 2098H Submitted on 28-5-2021 at 16:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga TORNADO 2098 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga TORNADO 2098 Manual

Product: