Manual Stiga SRC 36 G (page 28 of 96) (All languages)

608758

Zoom out

Zoom in

1/96

3.2

Hoeing and loosening the ground

To begin working:

– adjust the strut to the desired height;

– move the auxiliary wheel to the high position;

– press the handle bar slightly to raise the milling cutters

from the ground;

– press the safety lever (1) and pull the milling cutter

engagement lever (2).

– lower the cutters so they can penetrate the ground and

move the machine forward.

Suggestions for a job well done

• Do not use the machine on wet ground as the clods

could be dicult to break up.

• With hard and dry ground, the depth required should

be reached through two crossed passages, not carried

out too deeply.

3.3

When work is nished

When work is nished:

– release the engagement lever (2);

– move the throttle lever to «STOP»;

– move the auxiliary wheel to the lowered position.

Disconnect the spark plug cap (1) before storing the ma-

chine or doing any other jobs on it.

4. ROUTINE MAINTENANCE

IMPORTANT - Routine and accurate maintenance is

essential in maintaining original machine safety and

performance levels.

Store the machine in a dry place.

1) Wear sturdy work gloves before cleaning, maintaining

or adjusting the machine.

2) Accurately wash the machine with water after each

use; remove debris and mud accumulated on the

milling cutters and under the guard to prevent it drying

and making the next removal dicult.

3) Paint on the inner guard parts may come o over time

due to the abrasive action of clods removed; if this

happens, promptly touch-up paint with rust-proof paint

to prevent rusting that could corrode the metal.

4) If accessing the lower part is necessary, only tilt the

machine on the side indicated in the engine manual,

following the relevant instructions.

5) Do not drip petrol onto the plastic parts of the engine or

the machine to prevent damaging them and remove all

traces of spilt petrol immediately. The warranty does

not cover damage to plastic parts caused by petrol.

4.1

Milling cutter replacement

The milling cutters do not need their cutting edges shar-

pened.

To replace a milling cutter:

– remove the cap (1);

– release the cotter pin (2), extract the pin (3) and remove

the external (4) and internal (5) milling cutters.

WARNING - The cutting parts of the milling cutter

CANNOT be disassembled from their supporting

plate. You must ALWAYS replace the entire plate

complete with cutting parts. Using a milling cutter

with one or more broken or missing cutters can be

dangerous and bad for machine safety and reliabi-

lity.

Original milling cutters with the following code must be

used on this machine:

118801761/0 (external milling cutter)

118801760/0 (internal milling cutter)

Reassemble the milling cutters (4) and (5) and restore the

relative pin (3), cotter pin (2) and cap (1).

4.2

Adjusting transmission

If you have any problems when starting the milling cutter

engagement lever, with engagement too violent or mil-

ling cutters that tend to slow down when penetrating the

ground, the engagement cable needs adjustment.

This operation must be done by the Customer Service

Centre nearest to you or by your Dealer.

5. ENVIRONMENTAL PROTECTION

Environmental protection should be a priority of conside-

rable importance when using the machine, for the benet

of both social coexistence and the environment in which

we live.

– Try not to cause any disturbance to the surrounding

area.

– Scrupulously comply with local regulations for the di-

sposal of packaging, deteriorated parts or any elements

with a strong environmental impact; this waste must not

be disposed of as normal waste, it must be separated

and taken to specied waste disposal centres where

the material will be recycled.

– When decommissioning, do not pollute the environ-

ment with the machine, hand it over to a disposal cen-

tre, in accordance with the local regulations in force.

For any doubts or problems, please do not hesitate to

contact your nearest Customer Service Centre or Your

Dealer.

Basic instructions for staring.
What oil is preferable Submitted on 24-3-2023 at 10:27
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga SRC 36 G in the language / languages: All languages as an attachment in your email.

The manual is 1,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga SRC 36 G Manual

Product: