n ATTACHMENT COUPLE (Fig. 14) After use, clean and grease the couple (2) through the grease nipple (1).
nCUTTER BAR MAINTENANCE The cutter bar requires good and frequent maintenance. A rst and essential operation is to wash and
clean the knife after each use. When the machine will not be used for long periods of time, the cutting bar and knife should be protected with corrosion
inhibiting products and antioxidants.
n CHANGING THE CUTTING KNIFE (Fig. 15) To remove the top knife to change or sharpen it, remove screws (1) and pull the knife out
with a pin push into hole (2). We recommend changing the knife after 2 or 3 sharpenings. The bottom knife should be changed after the cutting knife has
been changed a coule of times though this will depend on the degree of wear. Always replace the plastic knife guide (3) when knifes are changed.
n SHARPENING THE CUTTING BLADE (Fig. 16) When the cutting blades are blunt (this will depend on work load) they must be
reground. Do not exceed 15 hours of work. In orde to do this, the cutting blade is removed from the bar and cleaned. It is essential to check whether
the backs and edges of the blades are bent; if so, they must be re-aligned. Only then can sharpening begin. Suitable for this purpose is a hand grinder
with about 15000 - 20000 revolutions per minute, in conjunction with a cup-shaped grinding point with a diameter of 25 mm and a length of about
35 mm. Only the front side (face) of the grinding point is used in grinding in a movement from the back of the blade to the blade’s edges. Cutter bar
blades need a cutting angle of 35 - 40°.
n CULTIVATOR MAINTENANCE (Fig. 17) Every time the rotary cultivator is used, the operator must check: -if the screws and nuts xing
the right and left spiders to the shaft are tightened all the way home; - if all the screws and nuts xing the spades are tightened all the way home.
Every 60 hours, check the oil in the gearbox by remove plug (1, Fig. 17). The oil must be level with the bottom of the hole. Change the oil every 150
work hours. To drain the oil, remove plug (1) and tip the cultivator over.
Drain the oil when the machine is hot.
When the oil has drained out completely, tip the machine back to its horizo,tal position and ll with new oil the bottom of the level hole. Replace the
plug.
nDESCRIPTION (Fig. 18) 1) Start-Stop operating lever 2) Drive operating lever 3) Cutter bar clutching control lever 4) Engine 5) Lever to
regulate the handlebar to the side. 6) Gear control rod.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Stiga SILEX 95 B at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Stiga SILEX 95 B in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.
The manual is 0,95 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
