608629
8
Zoom out
Zoom in
Previous page
1/18
Next page
22
ENGLISH
EN
b. Putting the gear in neutral and activating the
parking brake.
c. Stopping the engine and removing the key.
Only use accessories that are approved by the
machine’s manufacturer.
The machine may not be used without
accessories/tools being installed in the
machine’s tool mounts. Driving without
accessories can have a negative effect on the
stability of the machine.
Take care when using grass collectors and other
accessories. These can alter the machine’s
stability. Particularly on slopes.
Disengage the drive to the accessories, shut off
the engine and disconnect the spark plug cable
or remove the starter key:
a. To remove sticks and rubbish or when the
discharge has become clogged.
b. To check, clean or service the machine.
c. To check whether damage has occurred and
to carry out any repairs before starting and
using the machine again after a collision with a
foreign object.
d. To check the machine if it begins to vibrate
excessively. (Check immediately).
Disengage the drive to accessories during
transport or when the machine is not in use.
Shut off the engine and disconnect the drive to
the accessories:
a. Before filling with petrol.
b. Before removing the grass collector.
c. Before adjusting the height setting, assuming
this cannot be done from the drivers position.
Reduce the acceleration when the engine is to
be stopped, and if the engine is equipped with a
fuel shut-off valve, this should be switched off
when the work is finished.
Take care with multiple blade decks as one
rotating blade can cause other blades to rotate.
The machine, equipped with original
accessories, must not be driven in any direction
on slopes with a gradient greater than 10º.
The cutting deck’s original blade(s) may not be
replaced with non-original devices intended for
e.g. moss scarification. If such devices are used,
the guarantee will cease to be valid. There is
also a risk of serious injury or damage to people
or property.
Take care when unloading and loading the
machine onto a trailer or lorry.
2.4 MAINTENANCE AND STORAGE
Tighten all nuts and screws so that the machine
is in safe working condition.
At regular intervals check that the cutting
deck’s blade screw(s) are properly tightened.
Regularly check the operation of the brakes. It
is important to maintain and repair the brakes if
necessary.
Never store the machine with petrol in the tank
in buildings where the fumes can come into
contact with open flames or sparks.
Allow the engine to cool before placing the
machine in a store.
To reduce the risk of fire, keep the engine,
silencer, battery and petrol tank free from grass,
leaves and surplus oil.
Check frequently whether there is any wear or
damage to the grass collector.
For the sake of safety, replace worn or damaged
parts.
Always use genuine spare parts. Non-genuine
spare parts can entail a risk of injury, even if
they fit the machine.
Replace damaged warning and instruction
stickers.
If there is no mechanical lock for the transport
position, the cutting deck must be lowered
when parked, stored or when the machine is left
unsupervised.
If the petrol tank is to be emptied, this must take
place outdoors.
Store the machine so that children cannot get to it.
The battery contains acid. In the event of
mechanical damage or overcharging, acid can
leak out.
Never overcharge the battery. Overcharging can
cause the battery to explode, throwing the acid
in all directions.
If acid comes into contact with the eyes or skin,
this can cause serious injuries. If any part of the
body has come into contact with acid, rinse
immediately with copious amounts of water and
seek medical assistance as soon as possible.
Fumes from acid that are inhaled cause damage
to mucous membranes and other internal
organs. Seek medical assistance if acid fumes
have been inhaled.
Acid causes serious damage to tools, clothes
and other material. Rinse away spilled acid
immediately with water.
Do not short circuit the battery’s terminals.
Sparks occur which can result in fire. Do not
wear metal jewellery which can come into
contact with the battery terminals.
In the event of damage to the battery casing,
cover, terminals or interference to the strip
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga Silent at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Silent in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info