Manual Stiga SGS 60 LI (page 14 of 75) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

608753

Zoom out

Zoom in

1/75

GB | Operating Instruction

- The charging unit heats up during the charging

process. Do not place the unit on a flammable surface

or operate it in a flammable environment. Fire hazard!

- Never open the battery cells. Hazard of short circuits!

- In case of damage to the battery, hazardous vapours or

fluids may escape. In case of incidental contact flush

with water and seek medical advice immediately. The

fluid may have irritating or caustic effects on the skin.

- Protect the battery from heat, intense insolation and

fire. Explosion hazard!

Chargingprocess:

To charge the battery connect the charging unit to an

electrical socket. Then connect the plug of the charging

cable to the charging socket of the grass and shrub

shears or trimmer (fig. 2)

The start of the charging process is indicated by the

green control light (X) fig. 2 at the end of the handle. If the

battery is completely empty the charging time is about 4

hours. After the charging process has been completed,

the electronic control automatically switches off the

charging process. The green control light extinguishes

thereby indicating the end of the charging process. It is

not required to monitor the charging time.

The charging unit and the handle of the tool heat up

during the charging process. This is nothing unusual.

Pull the plug of the charging unit if it is not in use.

The tool must never be switched on during the charging

process!

Recharge the battery every time you realise a

considerable decrease of the tool’s cutting performance.

The battery additionally features an electronic total

discharge protection that protects the battery from

damage. This feature switches the battery off if the

discharging threshold is reached. Do not switch the tool

on afterwards and make sure to recharge the battery

first.

Switching the tool on/off

Slide the switch-on lock A (fig. 3) forward and push

switch B. After the tool has been switched on, you do not

have to hold the switch-on lock A any longer.

To switch off just let go of the switch B.

Attention! The blades will coast for a certain time

after switch-off!

Refitting the tool / Changing the shear

systems

Put the included blade guard into the blade(s) and use

protective gloves to protect yourself from injury.

Push both lateral push buttons concurrently and remove

the shearing blades (Fig. 5).

Remove any dirt from the gear area (if necessary).

Please slightly grease the drive area using commerci-

al universal grease as described in the Maintenance

section before putting the replacement shears in place

(Fig. 7).

Lead the cutting blades with the rear holding toe into

the housing of the grass shears as shown in fig. 6 and

lock the click system in place by strongly pushing on the

blade base plate.

The position of the eccentric drive does not have to be

considered when changing the blades. When the device

is switched on, the gear eccentric unit automatically en-

gages into the appropriate relief in the shearing blade.

The device is now ready for operation.

Hints for your work with the tool

The shrub trimmer cuts ornamental shrubs and light

undergrowth or bushes. The device is also well-suited

for ornamental cuts as, for example, for the care of

graves. As the device is operated with one hand please

be careful not to move the other hand near the running

cutting tools.

The grass shears allow for clean cuts of lawn edges or

hardly accessible lawn areas.

For convenient working in an upright position, the

included telescopic handle may be assembled to the

tool.

Maintenance (Fig. 7)

Clean the blade from any crushed plants and dirt. The

blades should be detached at least once a season for

the removal of debris. Lubricate the C pinion and the D

back of the blade with a light oil. Do not lubricate the mo-

tor and other parts. Should the blade become dull after a

long period of use, a spare part can be ordered.

Warning! The leading edges of the blades must be oiled

to ensure proper lubrication. If the leading edges are not

oiled, blade durability may be adversely affected.

If the cutting tools have become dull after long use

please replace them with original spare parts.

Clean the device using only a brush or cloth. Do never

wash down the device with water and do never dip the

device into water.

Apply protective spray to the blades after each use.

Replace blunt blades.

Always put on the blade guard after use.

Examine the tool for obvious defects and have it repaired

in an authorised service shop if required.

Storage

Always store the tool in a dry, clean place outside the

reach of children. Make sure that the place of storage

is frost-free.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga SGS 60 LI in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga SGS 60 LI Manual

Product: