733497
26
Zoom out
Zoom in
Previous page
1/357
Next page
PACKAGING CONTENTS
The packaging contains:
power unit,
bar,
chain,
bar cover,
bag containing equipment and documents.
The machine is supplied with
the bar and chain dismantled and the oil tank
empty.
Unpacking and complet-
ing the assembly should be done on a flat and
stable surface, with enough space for machi-
ne handling and its packaging, always making
use of suitable equipment.
Disposal of the packaging should be done in
accordance with the local regulations in force.
BAR AND CHAIN MOUNTING
Always wear heavy-duty
gloves when handling the bar and chain.
Mount the bar and chain very carefully so as
not to impair the safety and efficiency of the m-
achine. If in doubt, contact your dealer.
Before fitting the bar, make sure the chain brake is
not engaged; this is done by pulling the front hand
guard right back towards the body of the machine.
Make sure the machine is
not plugged into the mains socket.
MACHINES WITH STANDARD
CHAIN TENSION ADJUSTER
Remove the rubber protection (1a), unscrew the
nut (1) and remove the guard to get to the drive
sprocket and the point where the bar is fitted
(Fig. 1).
Mount the chain in the right direction on the bar.
If the tip of the bar has a nose sprocket, make
sure the drive links are correctly inserted in the
sprocket rims (Fig. 2).
WARNING!
WARNING!
WARNING!
IMPORTANT
Mount the bar (2) by inserting the stud bolt in the
groove and push it towards the back of the ma-
chine body and wind the chain around the drive
sprocket (Fig. 3).
Check that the chain tension adjuster pin (3) is fit-
ted properly in the hole on the bar (Fig. 4); if it is-
n’t, turn the chain tension adjuster screw (4) us-
ing a screwdriver until the pin is completely
inserted (Fig. 5).
Fit the guard back on without tightening the nut
(1).
Turn the chain tension adjuster screw (4) to ad-
just the chain tension (Fig. 5).
Raise the bar and tighten the guard nut (1) se-
curely using the supplied wrench, then replace
the rubber protection (1a) (Fig. 6).
MACHINES WITH QUICK CHAIN TENSION
ADJUSTER
Unscrew the handle (11) and remove the
guard to get to the drive sprocket and the point
where the bar is fitted (Fig. 1a).
Mount the chain in the right direction on the bar.
If the tip of the bar has a nose sprocket, make
sure the drive links are correctly inserted in the
sprocket rims (Fig. 2).
Mount the bar (2) by inserting the stud bolt in the
groove and push it towards the back of the ma-
chine body and wind the chain around the drive
sprocket (Fig. 3).
Fit the guard back on without tightening the han-
dle (11). Check that the chain tension adjuster
pin (3) is fitted properly in the hole on the bar
(Fig. 4); if it isn’t, turn the chain tension adjuster
ring-nut (12) until the pin is completely inserted
(Fig. 5a).
Turn the ring-nut (12) to obtain the desired chain
tension level (Fig. 5a).
Raise the bar and tighten the handle (11) se-
curely (Fig. 6a).
6MACHINE ASSEMBLY
EN
4. MACHINE ASSEMBLY
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga SE2016Q at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga SE2016Q in the language / languages: All languages as an attachment in your email.

The manual is 6,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info