608718
115
Zoom out
Zoom in
Previous page
1/408
Next page
The references  for correct sharpening are given 
in Fig. 20:
A = Incorrect sharpening
B = Sharpening limits
C = Incorrect and unequal angles
It is  important to  retain the correct balance after 
sharpening.
3 or 4 point blades can be used from both sides. 
When one side of the points is worn, the blade can 
be turned and the other side used.
WARNING!
The blade must never be
repaired, but must be replaced as soon as
signs of breaking are noted or the sharpening
limit is exceeded.
HEAD LINE REPLACEMENT (Fig. 21)
–  Follow the sequence indicated in the gure.
SHARPENING THE LINE CUTTING KNIFE
(Fig. 22)
–  Remove the line cutting knife (1) from the guard 
(2) by unscrewing the screws (3).
–  Fix the line cutting knife in a vice and sharpen it 
using a at le, being careful to retain the origi-
nal cutting angle.
–  Ret the knife on the guard.
EXTRAORDINARY MAINTENANCE
All maintenance operations not foreseen in  this 
manual must be  performed  exclusively  by  your 
dealer.
All and any operations performed in unauthorised 
centres or by unqualied persons will totally invali-
date the warranty.
STORAGE
After  every  work  stint,  clean  the  machine  thor-
oughly to remove all dust and debris, and repair 
or replace any faulty parts.
The machine must be stored in a dry place away 
from the  elements  and  with  the  cover  correctly 
tted.
LONG PERIODS OF DISUSE
IMPORTANT
If you are not going to use the
machine for a period of more than 23 months, we
recommend you do a few things before putting it
away. This will make it easier when you want to
use the machine again and will also prevent per-
manent damage to the engine.
• Storage
Before putting the machine away:
–  Empty the fuel tank.
–  Start the engine and run it idle until it comes to 
a halt, so that it uses up all the fuel that is left in 
the carburettor.
–  Wait for  the engine to  cool down and  remove 
the spark plug
–  Pour a teaspoon of fresh oil into the spark plug 
hole.
–  Pull the starter rope several times to deliver oil 
to the cylinder.
–  Replace the  spark  plug  with  the piston in the 
dead end upper position (visible from the spark 
plug slot when the piston is at maximum stroke).
•  Restarting work
When you wish to start using the machine again:
–  Remove the spark plug.
–  Pull  the  starter  rope  a  few  times  to  eliminate 
excess oil.
–  Check the spark plug as described in chapter 
“Checking the spark plug”.
–  Prepare the machine as indicated in the para-
graph entitled “Preparing for work”.
MAINTENANCE AND STORAGE  113
EN
115


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga B 33 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga B 33 in the language / languages: All languages as an attachment in your email.

The manual is 7,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info