608718

Stiga B 33 Manual

107
Zoom out
Zoom in
Previous page
1/408
Next page
en closure.
4)  To reduce re hazards, keep the engine, ex haust 
silencer and fuel storage area free from saw dust, 
branches, leaves, or excessive grease; ne ver leave 
containers with the cut debris inside the storage 
area.
5)  If the fuel tank has to be emptied, this should be 
done outdoors once the engine has cooled down.
6)  Always  wear  protective  gloves  when handling 
the cutting device.
7)  For safety reasons, never use the machine 
with worn or damaged  parts.  Damaged  parts 
are  to  be  replaced  and  never  repaired.  Only 
use original spare parts. Parts that are not of the 
same quality can seriously damage the equipment 
and compromise safety. The cutting tools must al
-
ways bear the manufacturer’s trademark as well as 
a reference to the maximum working speed.
8)  Before  putting  the  machine  away,  check  you 
have removed wrenches or tools used for main
-
tenance. 
9)  Store the machine out of the reach of children!
E)  TRANSPORTATION AND HANDLING
1)  Whenever the machine is to be handled or trans
-
ported you must:
–   turn o the engine, wait for the cutting device to 
stop and disconnect the spark plug cap;
–  t the cutting device guard;
–   only hold the machine using the handgrips and 
position the cutting device in the opposite direc
-
tion to that used during operation.
2)  When using a vehicle to transport the machine, 
position it so that it can cause no danger to persons 
and fasten it rmly in place to avoid it from tip ping 
over, which may cause damage or fuel spil lage.
F) HOW TO READ THE MANUAL
Certain paragraphs in the manual contain particu
-
larly signicant information and  are  marked  with 
various  levels  of  highlighting  with  the  following 
meaning:
NOTE
or
IMPORTANT
These give details or further
information on what has already been said, in the
aim to prevent damage to the machine.
WARNING!
Nonobservance will re sult
in the risk of injury to oneself or others.
DANGER!
Nonobservance will re sult
in the risk of serious injury or death to one self
or others.
2)  Mow only in daylight or good articial light.  
3)  Take on a rm and well-balanced position:
–   where possible,  avoid working on  wet,  slippery 
ground or in any case on uneven or steep ground 
that does not guarantee stability for the operator;
–   never run, but walk carefully paying attention to 
the lay of the land and any eventual obstacles;
– assess  the  potential  risks  of  the  ground  to  be 
mown and take all necessary precautions to en
-
sure your own safety, especially on slopes or on 
bumpy, slippery or unstable ground;
– work  along  the  contour  on  slopes,  never  when 
walking up or down and always keep downhill 
of the cutter.  
4)  Make sure the machine is securely locked when 
you start the engine:  
–   start the motor in an area at least 3 metres from 
where you refuelled;
–   check that there is nobody within at least 15 me-
tres of the machine’s range of action or at least 30 
metres for heavier mowing;
–   do not direct  the silencer  and therefore  the ex
-
haust fumes towards inammable materials.
5)  Do not change the engine governor settings 
or overspeed the engine.
6)  Do not strain the machine too much and do not 
use a small machine for heavy-duty works. If you 
use the  right machine, you  will reduce the  risk of 
hazards and improve the quality of your work. 
7)  Check  that  when  the  machine  is  running  idle, 
there is no movement of the cutting device and, af-
ter pressing the throttle trigger, the engine quickly 
returns to minimum speed.
8)  Ensure that the blade does not come into violent 
contact with foreign bodies and beware of the pos-
sibility of material being thrown up by the bla des.
9)  Always keep the machine connected to the web-
bing when working.
10)  Stop the engine:
–   whenever you leave the machine unattended.  
–   before refuelling.
– during movements between work areas. 
11)  Stop the engine and disconnect the spark 
plug cable:
–   before cleaning, checking or working on the ma-
chine;
–   after striking a foreign object. Inspect the ma-
chine for any damage and make repairs before 
restarting it again; 
–   if the machine starts to vibrate abnormally: nd 
the cause of the vibration immediately and have 
it inspected at a Specialised Centre.
–  when the machine is not in use.  
D)  MAINTENANCE AND STORAGE
1)  Keep all nuts, bolts and screws tight to be sure 
the equipment is in safe working condition. Rou-
ti ne maintenance is essential for safety and for 
maintaining a high performance level.
2)  Do not store the machine with fuel in the tank in 
an area where the fuel vapours could reach an o pen 
ame, a spark or a strong heat source.
3)  Allow  the  engine  to  cool  before  storing  in  any 
SAFETY REQUIREMENTS 105
EN
… 107 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga B 33 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga B 33 in the language / languages: All languages as an attachment in your email.

The manual is 7,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info