516571

Stiga Autoclip 325 Manual

23
Zoom out
Zoom in
Previous page
1/578
Next page
21
User’s manual
EN
REMOTE CONTROL: (only for some versions, see “Technical Specifi cations).
See the instructions on the remote control / console for the pairing procedure.
SOUND: Allows disabling the acoustic signal when the robot is in the charging station.
BACK TO RECHARGE: Allows selecting the method for the robot’s return to the charging
station.
1. “Follow wire”. The robot returns to the charging station by positioning the wheels on
either side of the perimeter wire.
2. “V-METER”. The robot runs along the perimeter wire at an indicative distance ranging
from a few centimetres to one meter (3.2 '), touching it every now and again in the
curved sections until it recognises the “Recall” to the charging station. Refer to the
“Installation” chapter.
DATE: Function for setting the date.
TIME: Function for setting solar or daylight saving time.
WORK SCHEDULES – PROGRAMMING MODE
WEEK: function for programming the operating days of the robot during the week. The
cursor automatically positions itself under the letter “M” (Monday).
Setting all the days at “1111111” means that the robot will work every day. Setting “0000000”
means that the robot will not work on any day of the week.
-
Value 1 : Robot’s work day.
-
Value 0 : Robot’s rest day.
Important
To get the best out of the robot, it is recommended to program the robot
to work every day.
WORK SCHEDULE 1: Function for setting the fi rst time of the robot’s working day.
The cursor automatically positions itself in the area under the fi rst time (e.g. 10:00am to
1:00pm). Set the time for the start and end of the work.
Setting the time at “00:00 – 00:00” means that the robot will not work during Work Schedule
1. Once entered. If the entered time is wrong such as if the time overlaps with the working
time 2 or if the starting time is after the end time, the robot beeps and resets the set value.
WORK SCHEDULE 2: Function for setting the second time of the robot’s working day.
Important
If it is necessary to set secondary areas, then it is preferable to program
both work schedules in order to increase the mowing frequency of the
area.
The setting of the time is essential for the robot’s proper functioning. Many parameters infl uence the setting of the work schedules, such as the
number of secondary areas, the number and the power of batteries of the robot, complexity of the lawn, type of grass, etc. Generally, the working
hours must be increased slightly when mowing gardens with secondary areas, with lots of obstacles and complicated areas. Below is a table with
the indicative times for confi guring the robot on fi rst use.
NB. Set all the weekdays at “1” – “Work Days.”
Model m² (ft²) Time 1 Time 2
075BA0 150 (1615) 11:00 11:40 15:00 15:30
075BA0 300 (3230) 11:00 17:00
075BA0 400 (4304) 11:00 19:00
075DE0 150 (1615) 11:00 11:40
075DE0 300 (3230) 11:00 11:40 15:00 15:40
075DE0 400 (4304) 10:00 16:00
075DE0 600 (6460) 10:00 19:00
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga Autoclip 325 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Autoclip 325 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 112,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info