516571

Stiga Autoclip 325 Manual

19
Zoom out
Zoom in
Previous page
1/578
Next page
17
User’s manual
EN
BATTERY CHARGING ON FIRST USE
1.
Place the robot inside the charging station.
2. Press the ON key.
3. After a few seconds, the “CHARGING” message will appear on the
display.
4. Press the “Start/Pause” key. The “PAUSE” function appears on the
display. The batteries start the charging cycle.
5. At the end of charging, the robot can be programmed for initial start-up
(see “Programming Mode”).
ENTER
“ON” KEY
“START/PAUSE” KEY
Important
On fi rst use, always charge the batteries for at least 4 hours.
ADJUSTMENTS
ADJUSTMENT RECOMMENDATIONS
Important
The user must make any adjustments according to the procedures described in this manual. Do not make any adjustments
which are not expressly indicated in this manual. Any special adjustments, not expressly indicated in this manual, must
only be performed by personnel from the Manufacturer’s authorised service centre.
ADJUSTMENT OF CUTTING HEIGHT
Before setting the cutting height of the blade, make sure the robot is safely off (see “Robot Safety Stop”).
Important
Use protective gloves to prevent injuries to your hands.
1. In models equipped with an antitheft alarm, disable it to prevent
activation. (See “Programming Mode”).
2. Turn over the robot and position it so as not to ruin the hood.
3. Unscrew the screw (C) and turn the bracket (E) in a clockwise direction
with the key provided.
4. Lift or lower the cutting unit (D) to set the desired cutting height. The
value can be measured using the graduated scale found on the key
provided.
Important
Do not use the robot to mow grass which is 1 cm (0.40 ")
higher than the cutting blade. Reduce the cutting height
gradually. It is recommended to reduce the height by at
least 1 cm (0.40 ") every 1-2 days until the ideal height is
reached.
5. Once the adjustment has been made, turn the bracket (E) in a counter-
clockwise direction and tighten the screw (C).
6. Turn the robot back over to its operating position.
(E)
cutting unit (D)
screws (C)
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga Autoclip 325 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Autoclip 325 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 112,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info