516583

Stiga Autoclip 127 Manual

29
Zoom out
Zoom in
Previous page
1/578
Next page
27
User’s manual
EN
Restarting
Before restarting the robot after a long period of inactivity, proceed as
follows:
1. Connect the plug of the power supply unit (A) to the electrical outlet.
2. Reconnect the main electrical power supply.
3. Position the robot inside the charging station.
4. Press the ON key.
5. Enter the password (if prompted) (See “Password Entry”).
6. After a few seconds, the message “CHARGING” will appear on the
display.
7. The robot is now ready to be used (see “Programming Mode”).
Current power
supplyunit (A)
Charging
station (C)
BATTERY CHARGING AFTER PROLONGED INACTIVITY
Danger - Attention
Do not recharge the robot in explosive and fl ammable
environments.
1. Supply electricity to the charging station and make sure the plates are
clean.
2. Position the robot inside the charging station.
3. Press the “ON” key (A).
4. Enter the password (if prompted) (See “Password Entry”).
5. After a few seconds, the message “CHARGING” will appear on the
display.
6. Press the “Start/Pause” key (B). The batteries start the charging cycle.
7. At the end of the charging cycle (approx. 6 hours), press the “OFF/
STOP” key (C).
8. Store the robot in a protected and dry place with an ambient temperature
between 10° and 20° C, diffi cult to reach by children, animals, other
foreign objects, etc.
ENTER
“START/PAUSE” KEY (B)
“OFF/STOP” KEY (C)
“ON” KEY (A)
OPERATING TIPS
Below are some useful operating tips to follow when using the robot.
-
Even after being suitably informed on the use of the robot, it is always a good idea to simulate some test manoeuvres on fi rst use to identify
the commands and main functions.
-
Check and secure the fastening screws of the main components.
-
Mow the lawn frequently to avoid excessive growth of the grass.
-
Do not use the robot to mow grass which is 1 cm (0.40 ") higher than the cutting blade. In case of high grass, lift the cutting blade and then
lower it gradually on the following days.
-
If the lawn is equipped with an automatic sprinkler system, program the robot to return to the charging system at least one hour before the
sprinklers are turned on.
-
Check the slope of the ground and make sure the maximum values allowed are not exceeded in order to prevent damage to the robot and
the sprinklers.
-
It is recommended to program the robot so that it does not work more than is necessary, also taking into consideration the different growth
rates of the grass in different seasons, so as not to subject it to unnecessary deterioration and reduction of the battery life.
-
When using the robot, make sure the work area is clear of people (in particular, children, the elderly or disabled people) and pets in order to
prevent safety risks. To minimise the chance of injury, program the robot so that it operates at suitable times of the day.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga Autoclip 127 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Autoclip 127 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 112,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info