608618
4
Zoom out
Zoom in
Previous page
1/5
Next page
ENGLISH
GB
MOWING HINTS
For the best effect follow this advice:
- mow regularly
- use full throttle on the engine.
- keep the underside of the mower deck clean.
- use sharp blades.
- do not mow wet grass.
MAINTENANCE
No service work to the engine or mower
deck is to be carried out unless the fol-
lowing action has been taken:
- the engine has been stopped.
- the ignition key has been removed.
- the ignition cable has been removed
from the spark plug.
- the parking brake is engaged.
- the mower deck has been disengaged.
CLEANING
Rinse off the underside of the mower deck casing
with a garden hose after using the mower.
If grass has dried onto the casing dismantle the
mower deck and scrape the underside clean.
If necessary, to improve the underside it can be
painted to prevent rust.
Do not spray with high pressure water
against the bearing housings on top of
the mower deck when the transmission
cover is removed. Otherwise water may
penetrate the bearings.
LUBRICATION
The attachment's support wheels are fitted with
two grease nipples J (fig 1). Lubricate using a uni-
versal grease periodically during the season.
Grease other moving parts too.
REPLACEMENT OF DRIVE BELT
CENTRAL BELT PULLEY - MOWER
DECK
1. Unhook the tension roller spring H.
2. Remove the mower deck from the machine.
3. Unscrew the screws K and remove the transmis-
sioncasing(fig4).
4. Slide in the unit towards the machine and pull
off the v-belt from the central belt pulley.
5. Change the damaged v-belt. Always use an orig-
inal v-belt. The tension roller G should rest to the
left of the v-belt as seen from the driver's seat
(fig 3).
6. Fit the screws K (fig 4).
7. Fit the mower deck in the machine's attachment
brackets.
8a. Park -1999:
Hook the tension roller spring H into the floor on
the right-hand side (fig 3).
8b. Park 2000-
Hook the tension roller spring H into the fastener,
just behind the front right wheel (fig 3).
REPLACEMENT OF THE DRIVE
BELT IN THE MOWER DECK
1. Remove the screws K and remove the transmis-
sion casing (fig 4).
2. Loosen the spring which holds the tension roller.
3. Change the v-belt and replace in the reverse or-
der. Always use original v-belts.
BLADES
Use protective gloves to prevent cuts
when changing blades/blade tips.
Make sure the blades are always sharp. This gives
the best cutting results.
SHARPENING
For safety reasons the blades must not be sharp-
ened on an emery wheel. Incorrect sharpening ( =
high temperature) can result in the blades becom-
ing brittle.
When the blades are due to be sharpened, the wet
grinding method with a waterstone or grindstone is
to be used.
Following sharpening, the blades must
be balanced to avoid vibration damage.
CHANGING BLADES
Always use original spare parts when changing the
blades, blade attachments or bolts.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga 110 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga 110 S in the language / languages: English as an attachment in your email.

The manual is 0,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info