Manual Stiebel Eltron RTI-E3 (page 9 of 20) (English, German, Dutch, French, Spanish)

469639

Zoom out

Zoom in

1/20

English

"CLICK"

X23

X21

X20

TA LE` LH LH` LE N

TALELHLHLENNNNNLL-SH

LNLE

L3 L2 L1

8/72

/40x

III

X15

X13

X12

X11

X10

X14

L3 L2 L1

X25

80 % PS

80 % NS

III

68/72 %

37/40 %

37/40

X15 X14

X13

TALELHLHLENNNNNLL-SH

LNLE

1 L3L2L1

80x PS

80x NS

68/72x AC

37/40x AC

III

8713.01

8715.01

8714.01

8716.01

⇒ Push the temperature selector button

(R2) into the operating panel and turn it

as far as the left-hand stop.

⇒ Rotate the shaft of the potentiometer as

far as the left-hand stop.

Engage the potentiometer into the opera-

ting panel from the switchbox side (check

that the potentiometer shaft is properly

located).

Lay the 3-pole connection lead of the po-

tentiometer along behind the angle plate

to the plug-in location of the discharge

control unit (in this situation, fix the con-

nection lead to the operating panel and

the angle plate by means of the cable

holder).

⇒ Pivot the angle plate located in the switch-

box forwards in order to accommodate

the mains connection terminals, after relea-

sing (not unscrewing) the screw located in

the rear wall.

⇒ Plug the connection lead (X25) on the di-

scharge control unit (A2) onto the charge

control unit (A1).

⇒ Guide the 6-pin plug connector of the di-

scharge control unit along behind the angle

plate and upwards, insert it form above

into the plug-in locations „TA“ to „N“ of

the connection terminal X2, and screw it

tight (push the cable harness into the cable

holder provided).

⇒ Plug the discharge control unit into the

longitudinal holes located above the charge

control unit and engage it in position.

⇒ Screw the room temperature sensor (B2)

with two screws (2.9 x 6.5) to the front

inclined edge of the baseplate. Plug the

connection cable into the plug-in location

X20 of the discharge control unit.

⇒ Plug the connection lead of the potentio-

meter into the plug-in location X21 of the

discharge control unit.

⇒ Guide the separate leads provided along

behind the angle plate and connect them

as shown in the following table (to the ter-

minals X1 and X2 from below):

from to

Lead (brown) LE`(X2) S2 (bottom

plug-in location)

Lead (black)

L (X1) S2 (top plug-

in location)

Designation Laying

The leads must not come in contact

with the operating panel conductor

plate or simply insulated leads for safety ex-

tra-low voltage (SELV).

Incorporate the leads to the S2 switch into

the existing cable harness (drillers can be

opened and then closed again).

⇒ Pivot the angle plate back to the rear again

and screw it tight.

⇒ Secure the side wall, front wall, and air out-

let and inlet grilles to the appliance once

again (respect the installation sequence).

The toothed disks must be inserted

beneath the securing screws of the

side wall and the front wall (protective con-

ductor connection).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron RTI-E3 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 4,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiebel Eltron RTI-E3 Manual

Product: