650337

Stiebel Eltron DHE 24 SLi Manual

33
Zoom out
Zoom in
Previous page
1/124
Next page
ENGLISH
www.stiebel-eltron.com DHE SLi | 33
INSTALLATION
Installation
Connecting a load shedding relay
Install the load shedding relay in the distribution board in conjunc-
tion with other electric appliances, e.g. electric storage heaters.
The relay responds when the instantaneous water heater starts.
The load shedding relay is available as an accessory.
!
Material damage
Connect the phase that switches the load shedding relay
to the indicated terminal of the mains terminal in the
appliance (see chapter "Specification / Wiring diagram").
Water installation for finished walls
Suitable pressure-tested taps can be ordered as accessories.
D0000033104
1
2
1 Water plug
2 Pressure tap for finished walls
Fit the water plugs with gaskets to seal the connection below
the plaster. With pressure taps listed in the accessories, the
plugs and gaskets are part of the standard delivery.
Install the tap.
Place the lower part of the back panel under the connection
pipes of the tap and push the lower part of the back panel
into place.
Secure the connection pipes to the appliance.
Water installation for finished walls with solder/ compression
fitting
You can connect copper or plastic pipes with solder fitting or
compression fitting accessories.
The solder fitting with threaded fitting is suitable for 12mm cop-
per pipes.
Push the union nuts over the connection pipes.
Solder the inserts to the copper pipes.
Push the lower part of the back panel under the connection
pipes of the tap and click the lower part of the back panel
into place.
Secure the connection pipes to the appliance.
Note
Observe the tap manufacturer's instructions.
Water installation for finished walls, fitting the appliance cover
D0000041391
4
3
2
1
1 Back panel guides
2 Screw
3 Cover guides
4 Knock-out
Cleanly break out the knock-outs in the appliance cover. If
necessary, use a file.
Note
If the tap connection pipes are slightly offset, the appli-
ance can be sealed using the tabs on the cover guides.
If the tap connection pipes are offset, do not fit any
back panel guides.
If installing tap connection pipes which are not offset, break
off the tabs on the cover guides.
Click the cover guides into place in the knock-outs.
Position the back panel guides on the pipes and push them
together. Then push the guides until they are resting against
the back panel.
Secure the back panel at the bottom with a screw.
Installation of lower part of back panel with threaded fitting
for finished walls
You can install the lower part of the back panel after fitting the
taps.
2
1
26�02�02�1080
1 Screw
2 Connection pieces from the pack
Cut open the lower part of the back panel at the markings.
Fit the lower part of the back panel by bending it out at the
sides and guiding it over the pipes.
Insert the connection pieces from behind into the lower part
of the back panel.
Click the lower part of the back panel into place.
Secure the lower part of the back panel with a screw.
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiebel Eltron DHE 24 SLi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron DHE 24 SLi in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 43,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info