650331
12
Zoom out
Zoom in
Previous page
1/20
Next page
 


2602�02�0821
3
1
2
1 Knock-out
2 Cap guides
3 Back panel guides
10.3.8 Installing lower part of back panel
If using threaded connections for finished walls, the lower part of
the back panel can also be installed after fitting the taps/valves.
To do this, carry out the following steps:
Cut open the lower part of the back panel.
Fit the lower part of the back panel by bending it out at the
sides and guiding it over the pipes.
Insert the connection pieces from behind into the lower part
of the back panel.
Click the lower part of the back panel into place.
Secure the lower part of the back panel with a screw.
2602�02�1080
21
3
1 Lower part of back panel
2 Connection piece from the pack
3 Screw
10.3.9 Installation in case of appliance replacement
An existing mounting bracket can be used when replacing Stiebel
Eltron appliances (except "DHF"). For this, open a suitable knock-
out in the back panel for the stud of the existing mounting bracket.
If the appliance is being installed in place of a DHF, move the
stud on the mounting bracket as shown in the diagram "Mounting
bracket for DHF appliance replacement". The stud cuts its own
groove. Then turn the mounting bracket through 180° to be
mounted on the wall. The logo "DHF" is then turned towards the
reader.
If replacing a third party appliance, suitable holes for rawl plugs
can be used.
2602�02�0815
10.3.10 Undersink installation with turned appliance cap
The appliance cap can be positioned on the back panel turned
through 180°. This particularly advantageous for undersink
installation. For this take the following steps:
Remove the user interface from the appliance cap by
pressing the locking hooks.
Turn the appliance cap and click the user interface into place,
ensuring that all locking hooks click into place. To install the
user interface more easily, press against the inner side of the
appliance cap (in the shaded area, see diagram "Appliance
cap for undersink installation").
!
Material damage
Never install a user interface with a faulty locking
hook. Otherwise the safety of the appliance cannot be
guaranteed.
Plug the set value transducer cable into the "set temperature"
PCB; see "Commissioning".
Hook the appliance cap in at the bottom and pivot it up onto
the back panel. Ensure the all-round seal of the back panel
sits tightly by pushing the cap gently forwards and back.
Close the appliance with the screw in the cap.
2602�02�0817
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiebel Eltron DHB-E 24 SLi electronic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron DHB-E 24 SLi electronic in the language / languages: English as an attachment in your email.

The manual is 7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stiebel Eltron DHB-E 24 SLi electronic

Stiebel Eltron DHB-E 24 SLi electronic Usermanual and installation guide - English, German, Dutch, French, Polish - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info