650329
10
Zoom out
Zoom in
Previous page
1/20
Next page
 


10.2.12 Fitting the lower back panel
2602�02�1102�
10.2.13 Completing the installation process
Align the mounted appliance by loosening the fixing
toggle, aligning the power supply and back panel, and
then retightening the fixing toggle. If the back panel of the
appliance is not flush against the wall, the appliance can be
fixed with a screw in the lower part.
10.3 Installation versions
10.3.1 Power supply from above for unfinished walls
The following diagram shows the dimensions for the power supply
from above.
2602�02�0802
To connect the power supply, take the following steps:
Open out the cable grommet to match the cross-section of
the power cable.
Push down and remove the locking hook that secures the
mains terminal.
Move the mains terminal in the appliance from the bottom to
the top and click into place.
2602�02�1123
10.3.2 Power supply for finished walls
The appliance can also be connected if the power supply has been
routed over finished walls. This applies to the connection from
below and above. Take the following steps:
Cut or break knock-outs in the back panel and appliance
cap. Possible knock-out points can be seen in the diagram
"Dimensions for power supply".
Note
If the appliance has been connected with a power supply
on finished walls, the type of protection on the type plate
must be changed from IP 25 to IP 24. Use a permanent
marker for that.
Cross out "IP 25" and mark the box "IP 24".
10.3.3 Power supply for large cross-sections
1.
3.
4.
2.
2602�02�1124
If cables with a large cross-section are used, the cable grommet
can be tted after the appliance has been installed. Take the
following steps:
Before installing the appliance, use a screwdriver to push the
cable grommet out.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiebel Eltron DHB-E 18 SLi electronic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron DHB-E 18 SLi electronic in the language / languages: English as an attachment in your email.

The manual is 7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stiebel Eltron DHB-E 18 SLi electronic

Stiebel Eltron DHB-E 18 SLi electronic Usermanual and installation guide - English, German, Dutch, French, Polish - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info