469621
14
Zoom out
Zoom in
Previous page
1/76
Next page
HTV`.HC
TT<.CZV.T`.HC
ĜÔCZ% qqqĪZ`.<é<`VHCĪHB
Never step on the appliance.
!
When using the mobile floorstanding unit, observe
the following:
Never cover the power cable with a carpet or
rug. Route the power cable away from walkways
to prevent anyone tripping over the cable or
knocking the appliance over.
Avoid using an extension cable. If this is
unavoidable, only use an undamaged extension
cable with a sufficient cable cross-section for
the full appliance output, as well as undamaged
plugs or coupler plugs and adequate protective
measures.
Position the appliance on a solid base. On a
soft base, the appliance can tip over or the air
apertures can become blocked.
Never move or carry the appliance by pulling on
the power cable.
If you use the appliance as a floorstanding unit,
never install it in the bathroom, in similarly damp
rooms or outside.
2.3 CE designation
The CE designation shows that the appliance meets all essential
requirements according to the:
Electromagnetic Compatibility Directive
Low Voltage Directive
2.4 Test symbols
See type plate.
The type plate is located on the right on the exterior of the
appliance.
3. Appliance description
The appliance is an electric direct heater and can be used as a
wall mounted appliance or alternatively as a mobile floorstanding
appliance with feet attached.
The appliance is suitable as a full heating system in bathrooms,
for example, or for use between seasons and as a booster heater
in smaller rooms, such as hobby and guest rooms.
The air in the appliance is heated by a heating element and
expelled via natural convection through the air outlet grille at the
top. Cool room air flows in through the apertures at the bottom
of the appliance.
After mounting the appliance to the wall or attaching the feet, and
making the electrical connection via the mains plug, the appliance
is ready for operation.
4. Operation
4.1 Description of the user interface
» Switch the appliance ON via the switch on the r.h. side of the
appliance.
» Set the required room temperature via the continuously variable
temperature selector (for temperatures see specification
chapter).
26_07_31_0037
As soon as the selected room temperature is reached, it is
constantly maintained at this selected temperature through
periodic heating (the output of the appliance must correspond at
least to the required heat demand of the room).
If several appliances are installed in a single room, the setting
at the temperature selector on each appliance can be different.
To avoid excessive power consumption when windows are open,
you should stop the appliance while venting.
4.2 Frost protection
» Turn the temperature selector as far to the right as possible. In
this position, the temperature controller switches on the heating
element automatically if the room temperature drops below the
frost protection temperature.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiebel Eltron CNS150F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron CNS150F in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info