742506
23
Zoom out
Zoom in
Previous page
1/92
Next page
INSTALLATION
Commissioning
www.stiebel-eltron.com CK 20 Premium | 23
ENGLISH
≥183≥183
D0000074798
Unhook the wall mounting bracket from the appliance.
Place the centred wall mounting bracket horizontally on the
floor. Mark holes1 and 2.
Lift up the wall mounting bracket so that its lower holes
match up with the markings you have just made on the in-
stallation wall.
Mark holes3 and 4 on the installation wall.
Drill the holes at the 4markings.
Secure the wall mounting bracket with suitable fixing ma-
terials (screws, rawl plugs). With the vertical slots, you can
compensate for an offset fixing hole.
10.3 Appliance installation
D0000074794
1
1 Wall mounting bracket
Hook the appliance onto the bottom tabs of the wall mount-
ing bracket by the slots in the back of the appliance.
Place the appliance in an upright position.
Secure the appliance by pushing it towards the wall until it
audibly snaps into place in the two upper springs on the wall
mounting bracket.
D0000074795
2
1
1 Appliance
2 Locking screw
Secure the appliance against unintentional release using the
supplied locking screw on the right or left-hand side of the
wall mounting bracket.
10.4 Removing the appliance
Undo and remove the locking screw from the wall mounting
bracket.
To release the appliance, push down the springs at the top of
the wall mounting bracket.
Tilt the appliance away from the wall and lift it off the bottom
tabs on the wall mounting bracket.
10.5 Electrical connection
WARNING Electrocution
- Carry out all electrical connection and installation
work in accordance with relevant regulations.
- Do not install the appliance with a fixed power
cable.
Material losses
- Observe the type plate. The specified voltage must
match the mains voltage.
- Ensure the on-site supply cable has an adequate
cross-section.
The appliance is supplied fully wired (with a mains plug), but it is
also suitable for permanent connection.
10.5.1 Connection to a standard socket
Plug the appliance into a standard socket.
10.5.2 Permanent connection to an appliance junction box
WARNING Electrocution
In the case of a permanent connection, the appliance
must be able to be separated from the power supply by
an isolator that disconnects all poles with at least 3mm
contact separation.
Material losses
- Trim the power cable so it leads directly to the appli-
ance connection socket.
- Ensure that, after trimming the power cable, the
appliance can still be removed from the wall without
a problem.
Trim the power cable by cutting off the plug.
Connect the power cable to a suitable appliance junction box.
11. Commissioning
The appliance is ready for operation as soon as it has been fixed
to the installation wall and connected to the mains.
Remove the protective film from the programming unit.
12. Troubleshooting
The power cable must only be replaced (for example if damaged)
by a qualified contractor authorised by the manufacturer, using
an original spare part.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiebel Eltron CK 20 Premium at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron CK 20 Premium in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 15,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info