742474

Stiebel Eltron BGC 2-60 Manual

14
Zoom out
Zoom in
Previous page
1/60
Next page
14 | BGC WWW.STIEBEL-ELTRON.COM
INSTALLATION
COMMISSIONING
10. Commissioning
!
Material losses
Boiling dry destroys the high limit safety cut-out and the
controller-limiter combination must then be replaced.
!
Material losses
If a heat exchanger is installed in the same cylinder, you
must limit the maximum temperature for this heat ex-
changer. This prevents the high limit safety cut-out of the
threaded immersion heater from responding.
Fill the system with water.
Turn the temperature selector to maximum temperature.
Switch the mains power ON.
Check the function of the appliance.
Check the function of the safety assembly.
10.1 Appliance handover
Explain the appliance function to users and familiarise them
with its operation.
Make users aware of potential dangers, especially the risk of
scalding.
Hand over these instructions.
11. Settings
Adjusting the temperature selection limitation
You can adjust the temperature selection limitation beneath the
temperature selector. At the factory, the appliance is limited to
60 °C.
Isolate the appliance from the power supply.
Set the temperature selector to “cold”.
Pull off the temperature selector.
60 °C
45 °C
1
2
26�02�79�0034
1 Limiter disc
2 Without limiter disc, maximum 80 °C
You can set the limit to 45 °C / 60 °C by rotating the limiter
disc. By removing the limiter disc, the maximum temperature
can be set.
Replace the temperature selector.
12. Troubleshooting
Note
The high limit safety cut-out can respond at temperatures
below –15 °C. The appliance may be subjected to these
temperatures during storage or transport.
Fault Cause Remedy
The water does not
heat up.
The high limit safety
cut-out has responded
because the controller
is faulty.
Remedy the cause of
the fault. Replace the
controller-limiter com-
bination.
The high limit safety
cut-out has responded
because the temperature
has dropped below -15 °C.
Press the reset button.
The high limit safety cut-
out has responded be-
cause a heat exchanger
in the same cylinder is
set too high.
Limit the maximum
temperature of the heat
exchanger.
The flanged immersion
heater is faulty.
Replace the flanged im-
mersion heater.
The safety valve drips
when the heating is
switched off.
The valve seat is con-
taminated.
Clean the valve seat.
1
26�02�79�0035
1 High limit safety cut-out reset button
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiebel Eltron BGC 2-60 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron BGC 2-60 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info