643151

Steinel XLED home 2 SL Manual

5
Zoom out
Zoom in
Previous page
1/7
Next page
– 8 –
– 9 –
GB
1� About this document
Please read carefully and keep in a safe place�
– Under copyright. Reproduction either in whole or
in part only with our consent.
– Subject to change in the interest of technical
progress.
Symbols
!
Hazard warning!
...
Reference to other information in the
document�
2� General safety precautions
!
Disconnect the power supply before
attempting any work on the unit�
• Installing these units involves work on the mains
voltage supply; installation must therefore be
carried out professionally in accordance with
the applicable national wiring regulations and
electrical operating conditions (
D
-VDE 0100,
a
-ÖVE/ÖNORM E 8001-1,
h
-SEV 1000)
• The light must be positioned so that it is not
expected that anybody can stare into the light
for any prolonged period from a distance of
less than 0.3 m.
• The floodlight enclosure heats up when the light
is on. Only adjust the angle of the LED panel
once it has cooled down. Do not look into the
LED light at short range or for any prolonged
period (> 5 min). You could damage your retina.
• Do not install the light on normally flammable
surfaces.
3. XLED home 2 SL /
XLED home 2 XL SL
Proper use
– LED floodlight suitable for wall mounting outdoors.
– Fully swivelling LED panel.
– Available as standalone floodlight or intercon-
nected with the master version.
With the fully swivelling panel, the floodlight can
be used at home to provide perfect illumination for
lighting up property, or commercially for lighting
up business premises. In conjunction with the opal
cover, this extremely ecient technology provides
wide-area lighting.
Models
– XLED home 2 SL
– XLED home 2 XL SL
Package contents (Fig� 3�1)
Floodlight adjustment range (Fig� 3�2 / 3�3)
Product dimensions (Fig� 3�4 / 3�5)
Product components (Fig� 3�6)
A LED panel
B Enclosure
C Wall mount
4� Electrical installation
Connecting the mains power supply lead
The supply lead consist of three wires:
L = phase conductor (usually black, brown or
grey)
N = neutral conductor (usually blue)
PE = protective-earth conductor (green/yellow)
If you are in any doubt, identify the conductors
using a voltage tester; then disconnect from the
power supply again. Connect the phase conductor
(L) and neutral conductor (N) to the terminal block.
Important:
Incorrectly wired connections will produce a short
circuit later on in the product or your fuse box.
In this case, you must identify the individual
conductors once again and reconnect them.
The light source of this luminaire cannot be
replaced. If the light source needs to be replaced
(e.g. at the end of its service life), the complete
luminaire must be replaced.
5� Mounting
• Check all components for damage.
• Do not use the product if it is damaged.
Mounting procedure
• Switch OFF power supply. (Fig� 3�7)
• Undo retaining screws. (Fig� 4�1)
• Detach enclosure (B) from wall mount (C).
(Fig� 4�2)
• Detach plug-in terminal (male) from wall mount.
(Fig� 4�3)
• Mark drill holes. (Fig� 4�4)
• Drill holes and insert wall plugs (Fig� 4�5)
• Fit sealing plug. (Fig� 4�6)
– Power supply lead, concealed (Fig� 4�7)
– Power supply lead, surface-mounted, with
spacers. (Fig� 4�8)
• Connect conductors. (Fig� 4�9)
• Connect plug-in terminal. (Fig� 4�10)
• Fit enclosure onto wall mount. (Fig� 4�11)
• Screw in retaining screws. (Fig� 4�12)
• Switch ON power supply. (Fig� 4�12)
6� EC Declaration of Conformity
This product complies with the requirements
defined in the following standards, legislation and
directives:
– Low Voltage Directive 2014/35/EU
– EMC Directive 2014/30/EU
– RoHS Directive 2011/65/EU
– WEEE 2012/19/EU
7� Warranty
This STEINEL product has been manufactured with
utmost care, tested for proper operation and safety
and then subjected to random sample inspection.
Steinel guarantees that it is in perfect condition
and proper working order. The warranty period is
5 years and starts on the date of sale to the con-
sumer. We will remedy defects caused by material
flaws or manufacturing faults. The warranty will be
met by repair or replacement of defective parts at
our own discretion. The warranty shall not cover
damage to wear parts, damage or defects caused
by improper treatment or maintenance. Further
consequential damage to other objects shall be
excluded. Claims under the warranty will only be
accepted if the unit is sent fully assembled and
well-packed with a brief description of the fault, a
receipt or invoice (date of purchase and dealer's
stamp) to the appropriate Service Centre.
Service:
Our Customer Service Department will repair faults
not covered by warranty or after the warranty
period has expired. Please send the product well-
packed to your nearest Service Centre.
GB
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel XLED home 2 SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel XLED home 2 SL in the language / languages: English, German, Swedish as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info