Manual Steinel US 360 (page 14 of 43) (English, German, Dutch, French, Italian, Polish, Swedish)

593152

Zoom out

Zoom in

1/43

- 26 - - 27 -

Potentiometer g

Potentiometer h

Potentiometer o

• Setting1min.–2hr.

• Turnedfullyclockwise:max

• Turnedfullyanti-clockwise:min

• Setting0sec.–10min.

• Turnedfullyclockwise:

Room surveillance

• Turnedfullyanticlockwise:

0 sec. (OFF)

Turning the potentiometer to the

"Surveillance" setting reduces the

sensitivity of the "Presence"

switching output.

The contact only closes on detect-

ing a pronounced movement, sig-

nalising with a high degree of cer-

tainty that persons are present.

The stay-ON time remains active.

The switch-ON delay is inactivated.

Switch-ON delay for switching output 2 HVAC

Reach adjustment

COM 2

Potentiometer i

Provides basic illumination for the

selected stay-ON time when ambi-

ent light falls below the selected

light-level threshold that is set.

This can be dimmed to 10% of

maximum light intensity. As soon

as a person enters the scene, the

detector switches either to 100%

light intensity (constant-lighting

controller OFF) or adjusts to the

preselected light level (con-

stant-lighting controller ON). When

no movement is being detected,

the detector dims back to basic

light level after the stay-ON time

expires. This is switched OFF when

stay-ON time (1 min. – 30 min.) has

expired or the daylight component

is sufficient to exceed the selected

level of brightness. In the ON set-

ting, the detector switches basic

light level ON and OFF as soon as

the level of light falls below the

light-level threshold.

Basic light level (DIM version)

Stay-ON time for switching output 2 HVAC

The reach required (response

threshold) is infinitely variable.

< US 360 / DualTech

at least 2 x 2 m - 6 x 6 m

presence

< Single US / Dual US

at least 3 x 3 m - 10 x 3 m

in each direction

Turned fully anticlockwise =

minimum reach

Turned fully clockwise

(factory setting) = maximum reach

The master/slave configuration

permits detection of movement in

large-type rooms or spaces (load

connected = master, no load =

slave). The level of brightness pre-

vailing in the room is only evaluat-

ed at the master. The slaves report

movements detected to the mas-

ter. Lighting or HVAC is switched

ON and OFF by the master only.

Master/slave

A parallel-connected configuration

also permits the use of several

masters. In this case, each master

operates the lighting group in ac-

cordance with the level of bright-

ness it measures. Delay times and

light-level thresholds are selected

at each master as required. The

switched load is spread among the

individual masters. Presence is still

detected collectively by all detec-

tors. The presence output can be

picked off from any master.

Master/master

Remote control

Using the remote control (option-

al), functions can be conveniently

activated from the floor.

Note: The pulse mode cannot be

overridden by the remote control.

Switch pulse mode OFF manually.

Presence Control remote control

unit: EAN no: 4007841 559410

Parallel-connected configurations

Two detectors linked with an

external stairwell lighting

timer

Old building / building

modernisation

External light source activated by

button. No twilight mode, day

mode only.

Detector as stairwell lighting

timer



14.1



14.2



14.3



14.4

When using several detectors, they

must be connected to the same

phase!

As many as 10 sensors can be

connected in parallel.

DIM detector



14.5

This external button cable is

not intended to serve as a

neutral conductor connec-

tion for loads (see page 6/7).



Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel US 360 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish as an attachment in your email.

The manual is 4,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel US 360 Manual

Product: