593132

Steinel sensIQ Manual

7
Zoom out
Zoom in
Previous page
1/68
Next page
- 13 -
Shroud foils
If the independent setting capability of the 3 sensors is not sufficient, you can additionally apply shroud foils (C), (D)
and (E) to limit the detection zone in the way you require (see illustration). Shroud foils (A) + (B) under the sensor sig-
nificantly impair the detection of small animals. This will, of course, prevent detection by these lenses, particularly the
sneak-by guard.
Note: Use of the shroud foil (A) may prevent the remote control from working (see Fig. ).
Hint: Apply a little water with cleaning agent to the lens and subsequently apply the shroud foil. In this way, the foil
does not firmly adhere immediately and you can conveniently make fine adjustments. Once the cleaner is dry, the
foil adheres.
If a mains switch is installed in the mains supply lead, the light is capable of the following functions in addition to the
simple ON/OFF function (wiring and ):
Manual override by power switch
Sensor operation
1) Switch light ON (when light is OFF):
Switch OFF and ON once. Light stays ON for the period selected.
2) Switch light OFF (when light is ON):
Switch OFF and ON once. The light goes out or switches over to sensor mode.
Manual override
1) Activate manual override:
Turn switch OFF and ON twice. The light is set to stay ON for 4 hours
(red LED lights up behind lens). Then it returns automatically to sensor mode
(red LED off).
2) Deactivate manual override:
Switch OFF and ON once. The light goes out or switches over to sensor mode.
5 sec. – 15 min.
1 x OFF/ON
4 hours
2 x OFF/ON
Twilight setting
(response threshold)
(Factory setting:
daylight operation 2000 lux)
The sensor's response threshold
can be set to between approx. 2 lux
and 2000 lux.
Note:
The desired twilight value can also be memorised by
remote control.
Reach setting
(Factory setting:
max. reach)
The reach can be adjusted in 3 directions by 3 control dials (100° respectively) independently from one another. The
table shows the reaches with different mounting heights and tangential walking direction. The values apply with flat
terrain and a temperature of 20 °C.
Time setting
(switch-off delay)
(Factory setting: approx. 10 sec.)
The desired duration of illumination
of the connected light is infinitely
adjustable between approx. 5 sec.
to max. 15 min.
Pulse mode:
If the controller is set to “ ”, the device is in pulse
mode, i.e. the output is switched on for approx. 2 sec.
(e.g. for an automatic stairwell system). Afterwards, the
sensor does not react to movement for approx. 8 sec.
Functions on the unit
The system can be put into operation once the mains
power has been connected and the unit is closed.
The sensor first carries out a calibration cycle lasting
40 – 50 sec. (LED flashes once a second).
Once calibration has been completed, several settings
can be made directly on the sensor or by remote control
(see section on “Remote control”).
5 sec. - 15 min.
2 – 2000 lux
2 – 20 m
- 12 -
Connection examples
Light without existing neutral conductor
Light with existing neutral conductor
Connection using two-circuit switch for manual
and automatic operation
Connection via two-way switch for manual
override and automatic operation
Position I: automatic operation
Position II: manual operation for permanent light ON
Note: the unit cannot be switched OFF, only optional
operation between settings I and II.
a) Load, max. illumination 2500 W
(see Technical specifications)
b) Sensor connection terminals
c) Indoor switch
d) Indoor two-circuit switch, manual, automatic
e) Indoor two-way switch, automatic, manual override
Connecting several sensors in parallel (not illustrated)
In this case, it is important not to exceed a sensor's
maximum connected rating. In addition, all units must
be connected to the same phase.
Technical specifications
Dimensions (H x W x D): 143 x 114 x 175 mm
Output:
Filament bulbs, 2500 W max., operating on 230 V AC
*1)
Fluorescent lamp, 1000 W max., at cos ϕ = 0.5, inductive load at 230 V AC
8 x 58 W each max., C ≤ 176 µF operating on 230 V AC
*2)
Switching capacity
softstart module: max. 100 W, trailing edge, only filament bulb
Connection: 220 – 240 V / 50 Hz (2.5 mm
2
max.)
Angle of coverage: 300° with 180° angle of aperture as well as sneak-by guard for coverage directly
below the sensor. Capability of masking out individual segments
Reach: Adjustable in 3 directions independently from one another by control dial,
(2 – 20 m max., temperature-stabilised)
Sensor technology: 4 sensors, 6 levels for long-distance detection and 5 for sneak-by guard,
1360 switching zones
Time setting: 5 sec. – 15 min., pulse mode (approx. 2 sec.)
Twilight setting: 2 – 2000 lux
Manual override: selectable (4 h)
Permanent light OFF: selectable (6 h)
IP rating: IP 54 through 2K-technology
Temperature ranging from: - 20° C to + 50° C
*1)
VDE tested
*2)
Fluorescent lamps, low-energy bulbs, LED lights with electronic ballast (total capacity of all connected ballasts below
the value specified).
Operation / Maintenance
The Infrared Sensor is suitable for switching light ON
and OFF automatically. The unit is not suitable for bur-
glar alarm systems as it does not provide the level of
sabotage protection that is prescribed for this purpose.
Weather conditions may affect the way the motion
detector works. Strong gusts of wind, snow, rain or hail
may cause the light to come ON when it is not wanted
because the sensor is unable to distinguish sudden
changes of temperature from sources of heat. The
detector lens may be cleaned with a damp cloth if it
gets dirty (do not use cleaning agents).
Declaration of conformity
This product complies with
- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
Mounting height
2
4
8
12
16
max
1.8 m
2 m
4 m
8 m
13 m
19 m
> 20 m
2.5 m
2 m
4 m
7 m
12 m
16 m
> 20 m
3 m
3 m
7 m
12 m
> 20 m
> 20 m
–
5 m
4 m
12 m
> 20 m
> 20 m
–
–
Stand-
ard
Setting,
control dial
1)
1)1)
1) Not recommended, restricted detection
GB
SensIQ_26spr_14-08-13_SensIQ_24spr.qxp 20.08.13 14:42 Seite 13
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel sensIQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel sensIQ in the language / languages: All languages as an attachment in your email.

The manual is 2,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info