Manual Steinel RS PRO LED S1 (page 5 of 55) (All languages)

593284

Zoom out

Zoom in

1/55

- 8 - - 9 -

Technische Daten

RS PRO LED S1 RS PRO LED S1 IP 65

Abmessungen (Ø x H) Kunststoff-Haube Ø 300 x 71 mm Ø 300 x 71 mm

Glas Ø 300 x 86 mm

Netzanschluss 230-240 V, 50/60 Hz 230-240 V, 50/60 Hz

Leistungsaufnahme 16 W (1,6 W Dimmbetrieb) 16 W (1,6 W Dimmbetrieb)

Lichtfarbe 3000 K (WW) / 4000 K (KW) 4000 K (KW)

Lichtstrom/Effizienz PC (KW) 734 lm - 45,70 lm/W PC opal 900 lm - 56,25 lm/W

PMMA (KW) 972 lm - 60,75 lm/W PC klar 1191 lm - 74,44 lm/W

Glas (KW) 887 lm - 55,43 lm/W –

PC (WW) 668 lm - 41,75 lm/W –

PMMA (WW) 950 lm - 59,38 lm/W –

Glas (WW) 808 lm - 50,50 lm/W –

Schutzart IP 20 IP 65

IK-Klasse PC IK07 IK10

PMMA IK03 –

Glas IK02 –

RS PRO LED S1 / RS PRO LED S1 IP 65

HF-Technik 5,8 GHz (reagiert temperaturunabhängig auf kleinste Bewegungen)

Erfassungswinkel 360° mit 160° Öffnungswinkel

Sendeleistung ca. 1 mW

Reichweite Ø 1-8 m

Max. Flächenabdeckung ca. 50 m²

Zeiteinstellung 5 sec. - 15 Min.

Dämmerungseinstellung 2-2000 Lux

Helligkeitsregulierung 10 % Dimmbetrieb

a) die ganze Nacht

b) 10 Min. nach Ablauf der eingestellten Zeit

c) 30 Min. nach Ablauf der eingestellten Zeit

Schutzklasse II

Temperaturbereich -10 bis +50 °C

Betriebsstörungen

SensorLeuchte

ohne Spannung

SensorLeuchte

schaltet nicht ein

SensorLeuchte

schaltet nicht aus

SensorLeuchte schaltet

ohne erkennbare Bewegung ein

SensorLeuchte schaltet trotz

Bewegung nicht ein

Störung

 Haussicherung defekt, nicht

eingeschaltet, Leitung unterbrochen

 Kurzschluss in der Netzzuleitung

 Eventuell vorhandener Netzschalter

aus

 neue Haussicherung, Netz schalter

einschalten, Lei tung überprüfen mit

Spannungsprüfer

 Anschlüsse überprüfen

 Netzschalter einschalten

 Dämmerungseinstellung falsch

gewählt

 Netzschalter AUS

 Haussicherung defekt

 neu einstellen

 einschalten

 neue Haussicherung,

evtl. Anschluss überprüfen

 dauernde Bewegung im

Erfassungsbereich

 Bereich kontrollieren

 Lampe nicht bewegungssicher

montiert

 Bewegung lag vor, wurde jedoch

vom Beobachter nicht erkannt (Be-

wegung hinter Wand, Bewegung ei-

nes kleinen Objektes in unmittel-

barer Lampennähe etc.)

 Gehäuse fest montieren

 Bereich kontrollieren

 schnelle Bewegungen werden zur

Störungsmini mierung unterdrückt

oder Erfassungsbereich zu klein

eingestellt

 Bereich kontrollieren

Ursache Abhilfe

Leuchte in Dauer-DIM

Keine Funktion

 Taster DIM Level 

im Install-Modus

 Taster DIM Level 

Install-Modus deaktivieren

Installation Instructions

Dear Customer,

Congratulations on purchasing your new STEINEL

SensorLight and thank you for the confidence you

have shown in us. You have chosen a pioneering

quality product that has been manufactured, tested

and packed with the greatest care.

Please familiarise yourself with these instructions

before attempting to install the product because

prolonged reliable and trouble-free operation will only

be ensured if it is fitted properly.

We hope your new STEINEL light will bring you

lasting pleasure.

System Components

Wall mount/ceiling mount

HF sensor

Spacer for surface wiring

IP65 sealing plug

 DIM-level button for installation purposes

Reach setting

Time setting

Light-level setting

Dip switch

Channel selection

Dimming functions

Snake-eye screws (optional)

Shrouds for partial limiting of the reach

Mains connection cable for concealed wiring

Mains connection cable for surface wiring

Example Applications

The RS PRO LED S1/S1 IP65 is an efficient light that

controls itself. A high-frequency sensor for detecting

persons, a light sensor for identifying the room's light-

ing situation as well as LEDs requiring no maintenance

provide efficient, instantaneous light. The facility of

868-MHz wireless communication (channel selection)

allows several lights to be interconnected in a room,

creating a group. Wireless communication to the next

light functions reliably over a distance of 50 m. All lights

then operate with equal rights and act as one large

light.

Principle

The SensorLight is an active motion detector. The

integrated HF-sensor emits high-frequency electro-

magnetic waves (5.8 GHz) and receives their echo.

The sensor detects the change in echo from even

the slightest movement in the light's detection zone.

A microprocessor then triggers the "switch light ON"

command. Detection is possible through doors,

panes of glass or thin walls.

Detection zones for ceiling mounting:

1) Minimum reach (1 m all round)

2) Maximum reach (8 m all round)

Detection zones for wall mounting:

3) Minimum reach (1 m all round)

4) Maximum reach (8 m all round)

Important: Persons or objects moving towards the

light are detected best.

Note:

The high-frequency output of the HF sensor is approx.

1 mW – that's 1000 times less than the transmission

power of a mobile phone or the output of a microwave

oven.

approx. 1 mW

approx. 1000 mW

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS PRO LED S1 in the language / languages: All languages as an attachment in your email.

The manual is 8,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel RS PRO LED S1 Manual

Product: