Manual Steinel RS PRO 5800 LED (page 6 of 13) (All languages)

593341

Zoom out

Zoom in

1/13

- 10 - - 11 -

Betriebsstörungen

Sensor-Leuchte ohne Spannung

Sensor-Leuchte schaltet nicht ein

Sensor-Leuchte schaltet nicht aus

Sensor-Leuchte schaltet ohne

erkennbare Bewegung ein

Sensor-Leuchte schaltet trotz

Bewegung nicht ein

Störung

M Haussicherung defekt,

nicht eingeschaltet, Leitung

unterbrochen

M Kurzschluss in der Netzzuleitung

M Eventuell vorhandener

Netzschalter aus

M neue Haussicherung,

Netz schalter einschalten,

Lei tung überprüfen mit

Spannungsprüfer

M Anschlüsse überprüfen

M Netzschalter einschalten

M Dämmerungseinstellung

falsch gewählt

M Leuchtstofflampe defekt

M Netzschalter AUS

M Haussicherung defekt

M neu einstellen

M Leuchtstofflampe austauschen

M einschalten

M neue Haussicherung,

evtl. Anschluss überprüfen

M dauernde Bewegung im

Erfassungsbereich

M Bereich kontrollieren

M Leuchte nicht erschütterungsfrei

montiert

M Bewegung lag vor, wurde

jedoch vom Beobachter nicht

erkannt (Bewegung hinter Wand,

Bewegung eines kleinen Objektes

in unmittelbarer Lampennähe etc.)

M Gehäuse fest montieren

M Bereich kontrollieren

M schnelle Bewegungen werden zur

Störungsmini mierung unterdrückt

oder Erfassungsbereich zu klein

eingestellt

M Vertauschter Anschluss der

Netzzuleitung (L und N)

M Bereich kontrollieren

M Anschlüsse L und N überprüfen

bzw. Phase prüfen

Ursache Abhilfe

Installation Instructions

Dear Customer,

Congratulations on purchasing your new STEINEL

IndoorSensorLight and thank you for the confidence

you have shown in us. You have chosen a high-quality

product that has been manufactured, tested and packed

with the greatest care.

Please familiarise yourself with these instructions before

attempting to install the SensorLight because prolonged,

reliable and trouble-free operation will only be ensured if

it is fitted and used properly.

We hope your new STEINEL IndoorSensorLight will bring

you lasting pleasure.

Principle

The SensorLight is an active motion detector. The inte-

grated HF-sensor emits high-frequency electromagnetic

waves (5.8 GHz) and receives their echo. In response to

the slightest movement in the light's detection zone, the

change in echo is perceived by the sensor. A microproces-

sor then triggers the "switch light ON" command. Detection

is possible through doors, panes of glass or thin walls.

Important: Persons or objects moving towards the light

are detected best.

Safety warnings

■ Disconnect the mains power before attempting any

work on the unit!

■ During installation, the electrical wiring you are

connecting must be dead. Therefore, switch off the

power first and use a voltage tester to make sure

the wiring is off circuit.

■ Installing the IndoorSensorLight involves work on the

mains voltage supply. This work must therefore be

carried out by a qualified electrician in accordance

with applicable national wiring regulations and

electrical operating conditions.

(D - VDE 0100,

A -ÖVE-ÖNORM E8001-1,  - SEV 1000)

■ Only use genuine replacement parts.

■ Repairs must only be made by specialist workshops.

These lights carry the D symbol and are suitable

for installation in workplaces exposed to the risk of

fire from dust or fibres.

Montagehöhe

2,50 m

6 m

2 m

Montagehöhe

2,50 m

6 m

2 m

Montagehöhe

2,50 m

6 m

2 m

Note:

The high-frequency output of the HF-sensor is

approx. 1 mW – that's 1000 times less than the

transmission power of a mobile phone or the

output of a microwave oven.

approx. 1 mW

approx. 1000 mW

Detection zones for ceiling mounting:

(at a mounting height of 2.5 m)

System Components

a Base

b HF-sensor

c Sealing plug

d Mounting clamp

e Metal shrouds

f Cover

g Support plate

h Hinged clip

i Mounting bracket

j LEDs

Mains connection

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS PRO 5800 LED in the language / languages: All languages as an attachment in your email.

The manual is 3,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel RS PRO 5800 LED Manual

Product: