Manual Steinel RS PRO 5200 (page 7 of 52) (All languages)

593351

Zoom out

Zoom in

1/52

- 12 - - 13 -

Technical specifications

Installation

To make the assembly procedure easier, please fit

the bracket  for mounting the support plate  after

installing the base .

Connecting the mains power supply lead (see Fig.).

The mains supply lead is a 3-core cable.

L = phase conductor (usually black or brown )

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

If you are in any doubt, identify the conductors using

a voltage tester; subsequently disconnect the power

supply again.

Note:

 Reversing the connections will result in a short-

circuit in the light unit or in your fuse box later on.

In this case, you must identify the individual con-

ductors once again and re-connect them. A mains

switch for switching the unit 'ON' and 'OFF' may of

course be installed in the mains power supply lead.

 When the diffuser is off the RS PRO 5002, do not

look directly into LED light for more than 100 sec.

 Make sure the installation site is not subject to

vibration.

Connecting a dimmer will result in damage to

the SensorLight.

Please note that the light must be protected by a

10 A circuit breaker.

L’ Connection of an additional load:

An additional load with max. 800 W can be connected

to the SensorLight, switched by the electronics. Screw

the live conductor to the load into the terminal mar-

ked L’ on the SensorLight. Clamp the neutral conduct-

or in the terminal marked N together with the neutral

conductor of the mains power supply lead. Attach the

protective-earth conductor to the earth terminal.

The SensorLight can be put into service after mount-

ing the light and connecting it to the mains power

supply. When putting the light into operation manually

at the light switch, it will switch 'OFF' after 10 sec. for

the calibration phase and is then activated for sensor

mode. It is not necessary to operate the light switch

a second time.

Reach setting (sensitivity)

Reach is the term used to describe

the diameter of the more or less

circular detection zone produced

on the ground after mounting the

SensorLight at a height of 2.5 m.

Turn the reach control fully anti-

clockwise to select minimum reach

(approx. 1 m dia.), and fully clockwise to select max-

imum reach (approx. 8 m dia.). (The light leaves the

factory set to maximum reach.)

Functions

1 m–8 m dia.

9.1

Time setting (switch-off delay)

The chosen light 'ON' time can be

set to any duration from approx. 1 min.

(setting control turned fully anti-

clockwise) to a max. of 20 min. (set-

ting control turned fully clockwise).

(The luminaire leaves the factory set

to the shortest time.) Any movement

detected before this time elapses will re-start the

timer. It is recommended to select the shortest time

for adjusting the detection zone and for performing

the walk test.

Note: After the light switches 'OFF', it takes approx.

1 second before it is able to start detecting movement

again. The light will only switch on in response to

movement once this period has elapsed.

Twilight setting (response threshold)

The chosen light response threshold

can be infinitely varied from approx.

2–2000 lux. Turn control fully anti-

clockwise to select dusk-to-dawn

operation at about 2 lux. Turn control

fully clockwise to select daylight

operation at about 2000 lux. (The

luminaire leaves the factory set to daylight operation.)

The control must be turned fully clockwise when

adjusting the detection zone and performing the walk

test in daylight.

Note: Apart from in the daylight setting, the luminaire

switches 'OFF' once an hour for 1 second at all other

twilight settings to measure the current twilight.

Hint: The easiest way of finding the desired light thresh-

old is to start by waiting for the surrounding brightness

at which the light function is to be activated. Set the

control dial to the fully anti-clockwise position and

allow the light to switch 'OFF'. Now turn the control

clockwise and let go as soon as the luminaire has

switched the light 'ON'. From now on, the luminaire

will always switch 'ON' and 'OFF' under these light

conditions.

LED basic brightness

(RS PRO 5002 LED only)

'ON' from approx. 2 lux. Can be switched 'OFF' by

remote control if preferred.

1 min. – 20 min.

Recommendation:

To ensure trouble-free HF-sensor operation, we

recommend seasoning the tubes by leaving them

switched

"ON" for 100 hours. This seasoning

process can increase tube life.

1. Connect light and switch "ON"

2. Turn all 3 setting controls fully clockwise, then turn

the middle setting control fully anticlockwise and fully

clockwise again (within 10 sec.)

The seasoning process is confirmed by switching the

light "OFF" twice and then back "ON" again.

4. Now turn all controls to the chosen settings.

5. The light is now left "ON" for 100 hours without

sensor function. Do not disconnect the light from the

mains power supply during this period.

6. The luminaire automatically returns to sensor mode

after 100 hours.

Note:

If tubes are not seasoned or ambient temperatures are

low, the sensor may not switch the light "OFF". In this

case, switch the light "OFF" and, for the time being,

drastically reduce the reach setting.

Please only use high-quality branded lamps.

Otherwise, we cannot guarantee that the high-

precision sensor will operate reliably.

2 - 2000 lux

9.2

9.3

Removing base



Dimensions (H x W x D)

RS PRO 5000/5002 LED/5200: 102 x 138 x 1266 mm

RS PRO 5100: 102 x 100 x 1266 mm

Mains power connection: 230 – 240 V/50 Hz

Output:

RS PRO 5000/5002 LED: 2 x 28 Watt / T5 (2 electronic ballasts) *

RS PRO 5200: 2 x 54 Watt / T5 (2 electronic ballasts) *

RS PRO 5100: 1 x 54 Watts / T5 (1 electronic ballast) *

RS PRO 5000/5002 LED/5200: max. of 2 further resistive loads of 800 W max., cos ϕ = 1

RS PRO 5100: max. of 4 further resistive loads of 800 W max., cos ϕ = 1

Output LEDs

RS PRO 5002 LED: 6.7 watts

HF-system: 5.8 GHz (responds to the tiniest movement regardless of temperature)

Angle of coverage: 360°, 160° angle of aperture *

(if applicable, through glass, wood or stud walls)

Transmission power: approx. 1 mW *

Reach: infinitely variable from 1 – 8 m dia. in 4 directions *

Max. area covered approx. 50 m

Time setting: 1 min. – 20 min. + install mode *

Twilight setting: 2 – 2000 lux + teach-in mode *

Temperature range: -10° C to +50° C

IP rating: IP 65, protection class I

Power consumption: 0.9 W

1) Must only be operated with the tubes specified, tube life is not impaired by switching 'ON' and 'OFF'

2) For sensor-control version only

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS PRO 5200 in the language / languages: All languages as an attachment in your email.

The manual is 2,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel RS PRO 5200 Manual

Product: