593352
8
Zoom out
Zoom in
Previous page
1/52
Next page
- 14 - - 15 -
Troubleshooting
SensorLight without power
SensorLight will not switch 'ON'
SensorLight will not switch 'OFF'
SensorLight switches 'ON' without
any identifiable movement
SensorLight does not switch 'ON'
despite movement
Malfunction
Fuse faulty in building's fuse
box, not switched 'ON', break
in wiring
Short circuit in mains power
supply lead
Any mains switch 'OFF'
Fit new fuse in building's fuse
box, turn mains switch 'ON',
check power supply lead with
a voltage tester
Check connections
Switch on mains power switch
Wrong twilight setting selected
Fluorescent lamp faulty
Mains switch 'OFF'
House fuse faulty
Adjust setting
Change fluorescent lamp
Switch 'ON'
Fit new fuse in building's
fuse box, check connection
if necessary
Continuous movement in
the detection zone
Check zone
Light installed on a surface
exposed to vibration
Movement occurred, but
not identified by the sensor
(movement behind wall,
movement of a small object
in immediate lamp vicinity etc.)
Securely mount enclosure
Check zone
Rapid movements are being
suppressed to minimise mal-
functioning or the detection
zone you have set is too small
Mains supply lead connected
the wrong way round (L and N)
Check zone
Check L and N connections
or check phase
Cause Remedy
Functional warranty
This STEINEL product has been manufactured with
great care, tested for proper operation and safety
in accordance with applicable regulations and then
subjected to random sample inspection. STEINEL
guarantees that it is in perfect condition and proper
working order. The warranty period is 36 months and
starts on the date of sale to the consumer. We will
remedy defects caused by material flaws or manu-
facturing faults. The warranty will be met by repair or
replacement of defective parts at our own discretion.
The warranty does not cover damage to wear parts,
damage or defects caused by improper treatment or
maintenance. Further consequential damage to other
objects shall be excluded.
Claims under the warranty will only be accepted if the
unit is sent fully assembled and well-packed with a
brief description of the fault, a receipt or invoice (date
of purchase and dealer's stamp) to the appropriate
Service Centre.
Repair service:
Our Customer Service Department
will repair faults not covered by war-
ranty or after the warranty period.
Please send the product well packed
to your nearest Service Centre.
Accessories
Remote control for RS PRO 5000/5002 LED
Prod. No. 737818
Declaration of conformity
This product complies with Low Voltage Directive
2006/95/EC, EMC Directive 2004/108/EC, RoHS
Directive 2002/95/EC, RTTE Directive 1999/05/EC
and Ballast Directive 2000/55/EC.
Instructions de montage
Cher client,
Nous vous remercions de la confiance que vous avez
témoignée à STEINEL en achetant cette lampe d'in-
térieur à détecteur. Vous avez choisi un article de très
grande qualité, fabriqué, testé et conditionné avec le
plus grand soin.
Avant de l’installer, veuillez lire attentivement ces instruc-
tions de montage. En effet, seules une installation et une
mise en service correctement effectuées garantissent
durablement un fonctionnement impeccable et fiable.
Nous souhaitons que votre nouvelle lampe d'intérieur à
détecteur vous apporte entière satisfaction.
F
Le principe
La lampe est équipée d’un détecteur actif de mouve-
ment. Le détecteur HF intégré émet des ondes élec-
tromagnétiques à haute fréquence (5,8 GHz) et reçoit
leur écho. Au moindre mouvement dans la zone de
détection de la lampe, le système détecte la modifi-
cation de l'écho. Un microprocesseur déclenche alors
la commande « Allumage de la lumière ». L’appareil
peut détecter les mouvements à travers les portes,
les vitres et les parois de faible épaisseur.
Zones de détection dans le cas d’un montage
au plafond :
1) Portée minimum (Ø 1 m)
2) Portée maximum (Ø 8 m)
Zones de détection dans le cas d'un montage mural :
3) Portée minimum (Ø 1 m)
4) Portée maximum (Ø 8 m)
Important : La détection sera optimale lorsque vous
vous déplacerez en direction la lampe.
Consignes de sécurité
Couper l'arrivée du courant avant toute intervention
sur l'appareil !
Pendant le montage, les conducteurs à raccorder
doivent être hors tension. Il faut donc d'abord
couper le courant et s'assurer de l'absence de
courant à l'aide d'un testeur de tension.
L’installation de la lampe d'intérieur à détecteur
implique une intervention sur le réseau électrique.
Elle doit donc être effectuée par du personnel
spécialisé conformément aux directives locales et
aux conditions de raccordement.
(D - VDE 0100,
A -ÖVE-ÖNORM E8001-1, - SEV 1000)
N’utiliser que des pièces de rechange d’origine.
Les réparations doivent être effectuées uniquement
par des ateliers spécialisés.
Avant de changer l’ampoule, mettez la lampe
hors tension.
Note :
La puissance haute fréquence du détecteur HF est
< 1 mW – ce qui ne représente qu’un 1000e de la
puissance d’émission d’un téléphone portable ou d’un
four à micro-ondes.
env. 1 mW
env. 1000 mW
Description de l’appareil
Châssis
Détecteur HF avec boutons de réglage
Filetage blindé
Pince de montage
Tôles de protection
Capot
Plaque de support
Pince de charnière
Réglage de la portée
Temporisation
Réglage de crépuscularité
Charnières
LED (RS PRO 5002 LED)
Raccordement au secteur sous crépi
Raccordement au secteur sur crépi
I
II
9.2
9.1
9.3
F
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel RS PRO 5100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS PRO 5100 in the language / languages: All languages as an attachment in your email.

The manual is 2,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info