592500
4
Zoom out
Zoom in
Previous page
1/54
Next page
- 7 -- 6 -
Betriebsstörungen
S
ensorLeuchte
ohne Spannung
SensorLeuchte
s
chaltet nicht ein
S
ensorLeuchte
schaltet nicht aus
SensorLeuchte schaltet
ohne erkennbare Bewegung ein
SensorLeuchte schaltet trotz
Bewegung nicht ein
Störung
Haussicherung defekt, nicht
eingeschaltet, Leitung unterbrochen
K
urzschluss in der Netzzuleitung
Eventuell vorhandener Netzschalter
a
us
neue Haussicherung, Netz schalter
e
inschalten, Lei tung überprüfen mit
Spannungsprüfer
A
nschlüsse überprüfen
Netzschalter einschalten
Dämmerungseinstellung falsch
gewählt
Netzschalter AUS
Haussicherung defekt
neu einstellen
einschalten
neue Haussicherung, evtl. Anschluss
überprüfen
dauernde Bewegung im
Erfassungsbereich
Bereich kontrollieren
Leuchte nicht erschütterungsfrei
montiert
Bewegung lag vor, wurde jedoch
vom Beobachter nicht erkannt
(Bewegung hinter Wand, Be-
wegung eines kleinen Objektes in
unmittelbarer Leuchtennähe etc.)
Gehäuse fest montieren
Bereich kontrollieren
schnelle Bewegungen werden zur
Störungsmini mierung unterdrückt
oder Erfassungsbereich zu klein
eingestellt
Bereich kontrollieren
Ursache Abhilfe
Installation instructions
D
ear Customer,
Congratulations on purchasing your new STEINEL
SensorLight and thank you for the confidence you
have shown in us. You have chosen a high-quality
product that has been manufactured, tested and
p
acked with the greatest care.
P
lease familiarise yourself with these instructions
before attempting to install the SensorLight because
prolonged reliable and trouble-free operation will only
be ensured if it is fitted properly.
We hope your new designer sensor-switched indoor
light will give you lasting pleasure and satisfaction.
G
B
System components
Enclosure
HF-sensor
Spacer for surface wiring
Reach setting (3 – 8 m all round)
Time setting (5 sec. – 15 min.)
Twilight setting (2 – 2000 lux)
Light diffuser
Mains connection, surface wiring
Mains connection, concealed wiring
II
I
Principle
T
he sensor-switched indoor light is an active motion
d
etector. The integrated HF-sensor emits high-fre-
quency electromagnetic waves (5.8 GHz) and
receives their echo. The sensor detects the change in
echo from even the slightest movement in the light's
detection zone. A microprocessor then triggers the
"switch light ON" command. Detection is possible
through doors, panes of glass or thin walls.
Detection zones for ceiling mounting:
1) Minimum reach (3 m dia.)
2) Maximum reach (8 m dia.)
Important: Persons or objects moving towards the
light are detected best.
Detection zones for wall mounting:
3) Minimum reach (3 m dia.)
4) Maximum reach (8 m dia.)
Safety warnings
n Disconnect the power supply before attempting any
work on the unit.
n The electrical connection lead must be dead during
installation. Therefore, switch
'
OFF
'
the power first
and check that the circuit is dead using a voltage
tester.
n Installing the sensor light involves work on the
mains voltage supply. This work must therefore
be carried out professionally in accordance with
applicable national wiring regulations and electrical
operating conditions.
(
D
-VDE 0100,
A
-ÖVE /
ÖNORM E8001-1,
-SEV 1000)
Note:
The high-frequency output of the HF sensor is approx.
1 mW – that's just 1,000th of the transmission power
of a mobile phone or microwave oven.
approx. 1 mW
approx. 1000 mW
GB
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel RS LED D2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS LED D2 in the language / languages: All languages as an attachment in your email.

The manual is 2,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Steinel RS LED D2

Steinel RS LED D2 User Manual - English, German, Polish, Spanish - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info