593313
5
Zoom out
Zoom in
Previous page
1/51
Next page
Installation instructions
Dear Customer,
Congratulations on purchasing your new STEINEL
SensorLight and thank you for the confidence you
have shown in us. You have chosen a high-quality
product that has been manufactured, tested and
packed with the greatest care.
Please familiarise yourself with these instructions
before attempting to install the SensorLight because
prolonged reliable and trouble-free operation will only
be ensured if it is fitted properly.
We hope your new STEINEL SensorLight will bring
you lasting pleasure.
GB
System components
Enclosure
Sealing plug
Twilight setting
(2 – 2000 lux)
Time setting
(1 min. – 15 min.)
Reach setting
(1 – 8 m all round)
HF-sensor
Plastic shade
Spacer for surface wiring
Shrouds for partially limiting reach
Grubscrew (prevents unintentional removal of
the plastic shade)
Principle
The SensorLight is an active motion detector. The
integrated HF-sensor emits high-frequency electro-
magnetic waves (5.8 GHz) and receives their echo.
The sensor detects the change in echo from even
the slightest movement in the light's detection zone.
A microprocessor then triggers the "switch light ON"
command. Detection is possible through doors,
panes of glass or thin walls.
Detection zones for ceiling mounting:
1) Minimum reach (1 m dia.)*
2) Maximum reach (8 m dia.)*
Important: Persons or objects moving towards the
light are detected best.
Detection zones for wall mounting:
3) Minimum reach (1 m dia.)*
4) Maximum reach (8 m dia.)*
Safety warnings
Disconnect the power supply before attempting
any work on the unit.
The electrical connection lead must be dead during
installation. Therefore, switch OFF the power first
and check that the circuit is dead using a voltage
tester.
Installing the SensorLight involves work on the
mains voltage supply. This work must therefore
be carried out professionally in accordance with
applicable national wiring regulations and electrical
operating conditions.
(
D -VDE 0100, A -ÖVE / ÖNORM E8001-1,
-SEV 1000)
Note:
The high-frequency output of the HF-sensor is approx.
1 mW – that's just 1,000th of the transmission power
of a mobile phone or microwave oven.
approx. 1 mW
approx. 1000 mW
- 9 -- 8 -
Betriebsstörungen
SensorLeuchte
ohne Spannung
SensorLeuchte
schaltet nicht ein
SensorLeuchte
schaltet nicht aus
SensorLeuchte schaltet
ohne erkennbare Bewegung ein
SensorLeuchte schaltet trotz
Bewegung nicht ein
Störung
Haussicherung defekt, nicht
eingeschaltet, Leitung unterbrochen
Kurzschluss in der Netzzuleitung
Eventuell vorhandener Netzschalter
aus
neue Haussicherung, Netzschalter
einschalten, Leitung überprüfen mit
Spannungsprüfer
Anschlüsse überprüfen
Netzschalter einschalten
Dämmerungseinstellung falsch
gewählt
Glühlampe defekt
Netzschalter AUS
Haussicherung defekt
neu einstellen
Glühlampe austauschen
einschalten
neue Haussicherung, evtl. Anschluss
überprüfen
dauernde Bewegung im
Erfassungsbereich
Bereich kontrollieren
Leuchte nicht erschütterungsfrei
montiert
Bewegung lag vor, wurde jedoch
vom Beobachter nicht erkannt
(Bewegung hinter Wand, Be-
wegung eines kleinen Objektes in
unmittelbarer Lampennähe etc.)
Gehäuse fest montieren
Bereich kontrollieren
schnelle Bewegungen werden zur
Störungsminimierung unterdrückt
oder Erfassungsbereich zu klein
eingestellt
Bereich kontrollieren
Ursache Abhilfe
GB
BDAL_RS 50_24spr.qxd 01.12.2010 14:44 Uhr Seite 9
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel RS 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS 50 in the language / languages: All languages as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info