Manual Steinel NightMatic 3000 Vario (page 4 of 53) (All languages)

592552

Zoom out

Zoom in

1/53

The factory-set twilight re-

sponse threshold of ap-

prox. 1 lux can be

changed as follows inside

the unit: At the ambient

light level you want the

light to come ON at,

press the button (see

drawing) with a ball-point

pen or similar object and

keep it pressed until the

LED indicator switches

ON and OFF again. Now

let the button go and the

ambient light level will be

sensed for approx. 10 sec.

(if necessary, the connect-

ed load will be switched

'OFF). From now on, the

light will switch ON under

these light conditions.

After connecting to the

mains power supply, the

load connected will light up

for approx. 8 seconds. Light

measurement will now be

activated.

Operation/Function

Twilight setting:

The light can be switched

'OFF' automatically at

night to save even more

electricity. Please use the

control dial inside the

housing for making the

setting which can be infi-

nitely varied. The unit

comes with a factory set-

ting that switches the light

'OFF' at approx. 1.30 a.m.

The electronic system

does not have a clock. All

times are computed by the

microprocessor on the ba-

sis of light levels at twilight.

Seasonal changes in light

levels are identified auto-

matically and taken into

account.

Night economy mode setting:

Examples of night economy mode:

The night economy mode

always ends in the early

hours of the morning

between approx. 4 and

5 p.m. After then, the light

switches 'ON' again auto-

matically when it gets dark

(factory setting).

This function can be

changed as follows:

Briefly press button until

the LED indicator lights up

and let button go. Now you

can choose between the

following settings:

LED indicator flashes

4 x = light switches ON

in the morning.

LED indicator flashes

2 x = light stays OFF in the

morning.

Setting for morning hours:

No night economy mode Mid-range night economy mode Long night economy mode

Installation Instructions



Dear Customer,

Many thanks for the trust

that you have shown in

purchasing your new

STEINEL NightMatic 3000

Vario. Please familiarise

yourself with these instruc-

tions before attempting to

install the unit. With hope

this high-quality product

brings you lasting satisfac-

tion.

The built-in photosensor

registers the ambient light

level and switches the con-

nected light ON in the

evening, OFF again in the

night economy mode

(when selected) and, if you

wish, ON again in the

early hours of the morning.

Wall mounting

Caution: Installation

means making connec-

tions to the mains power

supply.

230 V means danger to life!

Therefore, switch off the

power first and use a volt-

age tester to make sure the

wiring is off circuit.

Installation of the photo-

cell controller involves work

on the mains power sup-

ply; this means it must be

done properly in accor-

dance with VDE 100.

Please note that the photo-

cell controller must be

protected by a 10 A circuit

breaker. The mains sup-

ply lead must be no

greater than 10 mm in

diameter.

If you wish, the NightMatic

3000 Vario can be installed

directly next to the light.

A microprocessor distin-

guishes between ambient

and lamp light, ensuring

constant light measure-

ment.

For optimum performance

it is recommended to oper-

ate the system without a

switch.

Using a screwdriver, undo

the four housing screws by

turning them anti-clock-

wise and remove the hous-

ing cover. Hold the elec-

tronic system's housing

against the wall and mark

where to drill the holes,

paying attention to any

wiring already existing in

the wall, drill holes; insert

wall plugs.

When installing, make sure

the wires are fed in from

below wherever possible.

Before screwing on the

housing, pierce through the

condensation water holes

at the bottom.

Power

The unit has the following

marked terminals:

N = neutral conductor

terminals (2 x, usually

blue)

L = phase conductor termi-

nal (usually black,

brown or grey)

L' = terminal for the swit-

ched phase. If you are

in any doubt, identify

the conductors using

a voltage tester.

Connect the live conduc-

tor (L) and the neutral

conductor (N) to the ter-

minals provided for this

purpose. Connect the

load supply conductor

(light) to the second neu-

tral conductor terminal (N)

and phase (L').

Any green/yellow protec-

tive earth conductor must

be connected to the ter-

minal provided.

Principle

Installation

LED button LED button LED button

Important: Getting the ca-

ble connections crossed

will produce a short circuit

in the unit or in your fuse

box. In this case, you must

check the identification of

all cables and re-connect

them.

Light

(Phase)

(Neutral

conductor)

'OFF'

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel NightMatic 3000 Vario in the language / languages: All languages as an attachment in your email.

The manual is 1,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel NightMatic 3000 Vario Manual

Product: