592447
6
Zoom out
Zoom in
Previous page
1/67
Next page
- 10 - - 11 -
System components
ON/OFF button
feed trigger
LED indicator
socket for charging cable
USB charger
glue stick
Operating principle
and handling
Before using for the first time, fully
charge the battery (2-3 hours) so
as to prolong its life. (see Charging/
Operation)
Insert glue stick into rear heating
duct.
When using the tool for the first time,
press the trigger several times to fill
the heating chamber with adhesive. It
may also be necessary to give the glue
stick a short push to help it move in.
To prevent the applicator from being
switched ON unintentionally, you
must press the button for approx.
2 sec. Green LED flashes for 15 sec.
Press trigger and apply glue to one
side.
Firmly press together the materials
being glued, correcting alignment if
necessary.
Final bonding strength is reached
after a very short time (approx.
2 minutes)!
Spot glueing is recommended on long
items with large surfaces.
Rigid foam (e.g. polystyrene) can also
be glued without a problem. Merely
remember to apply the hot glue on
the base surface and not on the
polystyrene.
When glueing textiles or similar
materials, it is recommended to
apply the hot glue in "wavy" lines.
Let the applicator cool down
after use.
Charging / Operation
The rechargeable battery in the neo 1
comes partially charged. Before using
the applicator for the first time, fully
charge the battery (approx. 2-3 hours) to
ensure full capacity.
The neo 1 cannot be used while it is
charging.
Interrupting the charge cycle will not
damage the rechargeable battery. The
battery can be recharged at any time
without shortening its lifespan.
"Electronic Cell Protection (ECP)"
protects the battery from exhaustive
discharge. If the battery runs flat, pro-
tective circuitry switches the neo 1 OFF
and glue is no longer heated.
Charging with USB charger
Button LED red LED green
ON/OFF Battery charging
Applicator ready for use for a limited period
Battery is fully charged, charge cycle is completed
Operation / glueing
Button LED red LED green
ON Switch ON. Press button for approx. 2 sec.
Green LED fl ashes for 15 sec.
Applicator ready for use
Applicator starts for a further 5 min. each time you
press the trigger
No glueing for 5 min.
Applicator switches OFF
Switch applicator back ON at button
Red and green LED fl ashes alternately after
applicator has been in use for approx. 20 min.
The applicator can now only be used for approx.
another 10 min.
Red LED fl ashes 1x
Battery fl at, start charging using USB charger
Dimensions (HxWxD): 179 x 40 x 65 mm
Power supply: 100-240 V, 50/60 Hz, micro-USB charger
Battery voltage: 3.6-V lithium-ion rechargeable battery
Heating-up time: under 15 seconds
Rechargeable-battery run time: approx. 30 minutes (continuous operation)
Battery charging time: 90% in 3 hours
Melt temperature: approx. 170 °C
Recommended glue sticks: genuine STEINEL
Crystal sticks, Prod. No 040413 /
Ultrapower sticks, Prod. No. 0405005
(Ø 7 mm)
Technical Specifications
GB
Bdal_NEO 1_26-spr.indd 10-11Bdal_NEO 1_26-spr.indd 10-11 11.07.13 14:4711.07.13 14:47
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel Neo 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel Neo 1 in the language / languages: All languages as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info