Manual Steinel L910 LED (page 6 of 12) (All languages)

592630

Zoom out

Zoom in

1/12

- 10 - - 11 -

System Components

Package contents (Fig. 1.1)

Product dimensions (Fig. 1.2)

Product components (Fig. 1.3)

Group interconnection by means of communi-

cation cable (Fig. 1.9)

Installation height/reach (Fig. 2.0)

Manual override function (Fig. 2.1)

A. Wall mount panes

b. Light enclosure

C. IR sensor

D. Group interconnection cover tab

Installation (Fig. 1.4 – 1.8)

The site of installation should be at least 50 cm

away from another light because heat radiated

from it may activate the system. At minimum

reach (5 m), the light should be installed at a

height of no more than 1.8 m. To obtain the

specified reach of 12 m, the sensor should be

installed at a height of no more than 2.2 m.

Connecting the mains and load supply lead

(1.9)

The leads consist of three wires:

L = phase conductor (usually black or brown)

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

K = communication cable (optional)

If you are in any doubt, identify the conductors

using a voltage tester; then disconnect from the

power supply again. Connect phase (L), neutral

conductor (N) to the terminal block. Mixing up

the connections will produce a short circuit later

on in the product or your fuse box. In this case,

you must identify the individual cables and

re-connect them. Insulate protective-earth con-

ductor (PE) and simply place it next to terminal

block.

Note: A mains switch for switching ON and OFF

may, of course, be installed in the mains supply

lead. A mains switch is required for the manual

override function (Fig. 2.1, see Manual override

function)

Group interconnection (Fig. 1.9)

Communication cable K permits internal

STEINEL group interconnection of L 900 LED

and L 910 LED. For this, the cover tab (F) in the

terminal compartment must be broken out at

the point marked (K). As many as 10 lights

can be interconnected with each other. The

communication cable must not be longer

than 50 m.

Note:

- No voltage must be connected to the com-

munication cable. No external loads must be

connected!

- Within the interconnected group, all lights

operate in line with their specific DIP-switch

settings.

- Group interconnection is not possible in test

mode.

Functions (Fig. 1.7)

Once installed, the sensor can be put into

operation. All pre-programmed functions are

selected at DIP switches 1-6. Factory setting:

DIP switches OFF

DIP 1 effect lighting

OFF = Sensor mode, main light/soft start

ON = effect lighting as from light-level setting

selected, main light activated by sensor

DIP 2 night economy mode, effect lighting

OFF = effect lighting ON all night

ON = effect lighting ON for half the night in

relation to setting selected at DIP 1

DIP 3 twilight setting (response threshold)

OFF = 20 lux

ON = 2 lux

DIP 4 time setting (switch-OFF delay)

OFF = 2 min

ON = 15 min

DIP 5 test mode

OFF = test mode deactivated

ON = test mode activated (5 sec)

Note:

Communication (optional group interconnec-

tion) to the interconnected lights is deactivated

in test mode. Only the light being tested is in

test mode. The other lights remain in group

mode

DIP 6 Reach setting (sensitivity)

OFF = 12 m

ON = 5 m

Manual override function (Fig. 2.1)

If a mains switch is installed in the mains sup-

ply lead, the following functions are provided

in addition to simply switching light ON and

OFF:

Manual override

1) Activate manual override:

Turn switch OFF and ON twice. The light is set

to manual override for 4 hours. Then it returns

automatically to sensor mode.

2) Deactivate manual override:

Switch OFF and ON once. Light goes out or

switches to sensor mode.

Important:

The switch should be actuated in rapid

succession (in the 0.2–1 sec. range).

Note:

When groups are interconnected, this

command is sent to all of the lights that

are connected.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel L910 LED in the language / languages: All languages as an attachment in your email.

The manual is 1,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel L910 LED Manual

Product: