Manual Steinel IS NM 360 (page 9 of 48) (English, German, Polish)

592543

Zoom out

Zoom in

1/48

1716

Troubleshooting

Sensor without power

■ Fuse faulty, not

switched "ON",

break in wiring

■ Short circuit

■ Fit new fuse; switch

"ON" mains switch;

check wiring with

voltage tester

■ Check connections

Sensor will not switch

"ON"

■ Twilight control set

to night-time mode

during daytime

operation

■ Bulb faulty

■ Mains switch "OFF"

■ Fuse faulty

■ Detection zone not

properly targeted

■ Internal electri-

cal fuse has been

activated (red LED

flashing rapidly)

■ Re-adjust

(control h)

■ Change bulb

■ Switch "ON"

■ Renew fuse,

check connection

if necessary

■ Re-adjust

■ Switch sensor

"OFF" and "ON"

again after approx.

5 sec.

Malfunction Cause Remedy

Sensor will not

switch "OFF"

■ Continued move-

ment in detection

zone

■ Sensor unit is not

properly engaged

■ Check detection

zone and re-adjust

if necessary

■ Lightly press sensor

unit to clip it into

place

Sensor doe not switch

"OFF" at around

midnight

■ External light

source (e.g. another

motion detector or

light) inactivating

the sensor

■ Shade sensor from

extraneous light,

observe sensor for

several days as it

takes time to return

to the correct value

Troubleshooting

Malfunction Cause Remedy

Sensor responds when

it should not

■ Wind is moving

trees and bushes in

the detection zone

■ Cars in the street

are being detected

■ Sudden change in

temperature due

to weather (wind,

rain, snow) or air

expelled from fans,

open windows

■ Change zone

■ Adjust detection

zone or change site

of installation

Sensor reach has

changed

■ Differing ambient

temperatures

■ Use shrouds to

define detection

zone precisely

Red LED flashing

rapidly

■ Internal fuse

activated

■ Switch light "OFF"

and "ON" again

after 5 sec.

Technical specifications

Output:

Filament bulbs, 1000 W max., operating on 230 V AC

Fluorescent lamp, 500 W max., at cos j = 0.5,

inductive load at 230 V AC

6 x 58 W each max., C ≤ 132 µF

operating on 230 V AC

*1)

Voltage: 230 – 240 V, 50/60 Hz

Angle of coverage: 360° with 90° angle of aperture and

sneak-by guard

Sensor reach:

8 m max. all round (mounted at a height of 1.75 – 2 m)

Time setting: 5 sec. – 15 min.

Twilight setting: 2 – 2000 lux

Programme setting: 4 function programmes geared to practical

requirements

ON time: selectable (4 hours) provided Switch in

mains power supply lead

Enclosure: IP 54

Temperature range: -20 °C to +50 °C

*1)

Fluorescent lamps, low-energy bulbs, LED lights with electronic ballast (total capacity

of all connected ballasts below the value specified).

IS NM 360_Osteuropa Vs_D.indd 19 15.10.12 11:22

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS NM 360 in the language / languages: English, German, Polish as an attachment in your email.

The manual is 2,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel IS NM 360 Manual

Product: