Manual Steinel IR 180 UP (page 10 of 44) (All languages)

592482

Zoom out

Zoom in

1/44

Functions

Contact-free switching

Move your hand in front of

the sensor unit at a dis-

tance of max. 5 cm and the

connected light will switch

on.The procedure is equally

simple when switching off.

Orientation light

The Sensor Switch

NF 50 UP is equipped with

a red LED. This serves as

an orientation light in the

dark, so that the switch is

easier to find.

Note:

Parallel switching or ex-

change of an existing two-

way circuit is not possible.

(only for NF 50 UP)

Technical specifications

IR 180 UP: NF 50 UP:HF 360 UP:

Note for IR 180 UP:

The installation position

should be at least 1 m from

a light, since heat radiation

may trigger the system.

Installation procedure:

1. Pull the mains lead out

of the flush box and strip

the insulation from the

individual leads.

Connecting the supply

lead (refer to Ill. on

page 5)

The mains lead consists of

a 3 phase cable.

L = phase conductor

(usually black or

brown)

N = neutral conductor

(usually blue)

L‘ = phase conductor

(usually black or

brown)

If in doubt, the cable must

be identified with a voltage

tester. Switch off the current

again. Phases (L) and (L‘)

in addition to the neutral

conductor (N) are connec-

ted to the terminal block. A

protective-earth conductor

is not required.

Important: Reversing the

connections may result in

damage to the unit.

2. Push the basic elem-

ent  into the flush box

 and arrange horizon-

tally. Take care that the

cables are not pinched.

Tighten both screws on

the expansion claw until

the basic element is firm-

ly seated or screw with

socket fixing screws on

the support ring.

3. Apply the cover frame 

and surround  and

carefully mount the sen-

sor unit  without tilting.

4. Once the mains connec-

tion has been made, the

sensor switch can be

operated (refer to Func-

tions section).

Only IR 180 UP and

HF 360 UP:

The adjustment controls for

the functions are concealed

behind the folding design

shade. Push in the catch on

the sensor unit with a screw-

driver and fold the design

shade forwards.

Note:

Parallel switching of

IR 180 UP and HF 360 UP

is possible. Nevertheless, a

neutral lead must be pres-

ent on each flush box. The

max. output to be switched

does not increase as a re-

sult.

* Installation above a door

(IR 180 UP / HF 360 UP / NF 50 UP)

Dimensions:

Output:

Connection:

Contact gap:

Installation height:

Sensor technology:

Transmission output:

Angle of coverage:

Reach:

Twilight setting:

Time setting:

Permanent light:

Permanent light OFF:

Orientation light:

(H x W x D) 80 x 80 x 55 mm

max. 1000 W (ohmic load, e.g. filament bulb)

max. 500 VA (uncompensated, inductive, cos ϕ = 0.5

e.g. fluorescent lamps )

230 V, 50 Hz

3-lead connection (L, L’, N)

µ, contact clearance of less than 1.2 mm between the

contacts when unit is switched off.

approx. 1.1 + 2.2 m*

Infrared sensor

180° with 90° angle

of aperture

max. 8 m

2 - 2000 lux

10 sec. - 30 min.

switchable (4 h)

switchable

approx. 1.1 + 2.2 m*

5.8 Ghz

High frequency

approx. 1 mW

360° with 140° angle

of aperture

1 - 8 m

continously adjustable

2 - 2000 lux

10 sec. - 30 min.

switchable (4 h)

switchable

approx. 1.1 m

5.8 Ghz

High frequency

approx. 1 mW

approx. 5 cm

red LED

Installation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IR 180 UP in the language / languages: All languages as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel IR 180 UP Manual

Product: