Manual Steinel FRS 30 (page 6 of 51) (All languages)

592489

Zoom out

Zoom in

1/51

Installation

To make the assembly procedure easier, please fit

the bracket  for mounting the support plate  after

installing the base .

Connecting the mains power supply lead (see Fig.).

The mains lead consists of a 3 phase cable.

L = phase conductor (usually black or brown)

N = neutral conductor (usually blue)

PE = protective-earth conductor (green/yellow)

If in doubt, a voltage detector must be used to identify

the lead; then switch off the power again.

Important: Reversing the connections will result in

a short-circuit in the light unit or in your fuse box

later on. In this case, you must identify the individual

conductors once again and re-connect them. A mains

switch for switching the unit ON and OFF may of

course be installed in the mains power supply lead.

Important: Make sure the installation site is

not sub-

ject to

vibration.

Connecting a dimmer will result in damage to the

SensorLight.

Please note that the light must be protected by a 10 A

circuit breaker.

Technical specifications

Output: 2 x 18 watts

plus 200 W max. (e.g. bathroom/WC fan extractor)

Mains power connection: 230 – 240 V/50 Hz

Installation site: indoors, ceiling mounting

HF-system: 5.8 GHz CW radar, ISM band

Transmission power: approx. 1 mW

Detection: 360°, 160° angle of aperture, if necessary through glass, wood and stud walls

Reach: 1 – 8 m dia., infinitely variable

Time setting: 1 min. to 15 min.

Twilight setting: 2 – 2000 lux

Enclosure: IP 65

Protection class: I

Power consumption: approx. 0.9 W

- 10 -

L’ Connection of an additional load:

An additional load with max. 200 W can be connected

to the SensorLight, switched by the electronics. Screw

the live conductor to the load into the terminal mar-

ked L’ on the SensorLight. Clamp the neutral conduct-

or in the terminal marked N together with the neutral

conductor of the mains power supply lead. Attach the

protective-earth conductor to the earth terminal.

The SensorLight can be put into service after mount-

ing the light and connecting it to the mains power

supply. When putting the light into operation manually

at the light switch, it will switch off after 10 sec. for

the calibration phase and is then activated for sensor

mode. It is not necessary to actuate the light switch a

second time.

Reach setting (sensitivity)

Reach is the term used to describe

the diameter of the more or less

circular detection zone produced

on the ground after mounting the

SensorLight at a height of 2.5 m.

Turn the reach control fully anti-

clockwise to select minimum reach

(approx. 1 m dia.), and fully clockwise to select max-

imum reach (approx. 8 m dia.). (The light leaves the

factory set to maximum reach.)

Time setting (switch-off delay)

The light can be set to stay ON for

any period of time between approx.

1 min. (control turned fully anti-

clockwise) and a maximum of 15 min.

(control turned fully clockwise).

(The light leaves the factory set to

the shortest time.) Any movement

detected before this time elapses will re-start the

timer. It is recommended to select the shortest time

for adjusting the detection zone and for performing

the walk test.

Note: After the light switches OFF, it takes approx.

1 second before it is able to start detecting movement

again. The light will only switch on in response to

movement once this period has elapsed.

Twilight setting (response threshold)

The chosen light response threshold

can be infinitely varied from approx.

2–2000 lux. Turn control fully anti-

clockwise to select dusk-to-dawn

operation at about 2 lux. Turn control

fully clockwise to select daylight

operation at about 2000 lux. (The

light leaves the factory set to daylight operation.) The

control must be turned fully clockwise when adjusting

the detection zone and performing the walk test in

daylight.

Recommendation:

Fluorescent tube manufacturers recommend season-

ing, or burning in, new tubes for 100 hours so as not to

restrict tube service life. To follow this recommendation

and to ensure trouble-free sensor operation particularly

at low ambient temperatures, new fluorescent tubes

should undergo the following seasoning procedure.

Functions

- 11 -

1 m – 8 m dia.

Functional warranty

This STEINEL product has been manufactured with

great care, tested for proper operation and safety

in accordance with applicable regulations and then

subjected to random sample inspection. STEINEL

guarantees that it is in perfect condition and proper

working order. The warranty period is 36 months

and starts on the date of sale to the consumer. We

undertake to remedy faults caused by material or

manufacturing defects. This warranty undertaking

shall be performed by the repair or replacement of

the defective parts, at our own discretion. The war-

ranty shall not cover damage to wear parts, damage

or defects caused by improper treatment or mainten-

ance. Further consequential damage to other objects

shall be excluded.

Claims under the warranty will only be accepted if the

unit is sent fully assembled and well packed with a

brief description of the fault, a receipt or invoice (date

of purchase and dealer's stamp) to the appropriate

Service Centre.

Repair Service:

Our Customer Service Department will

repair faults not covered by warranty

or after the warranty period. Please

send the product well packed to your

nearest Service Centre.

Declaration of Conformity

This product complies with Low Voltage Directive

06/95/EC, EMC Directive 04/108/EC, RoHS Directive

02/95/EC, RTTE Directive 99/05/EC and Energy

Efficiency Directive 00/55/EC.

1 min. – 15 min.

2 - 2000 lux

1. Connect light and switch ON

2. Turn all 3 setting controls fully clockwise, then turn

the middle setting control fully anticlockwise and fully

clockwise again (within 10 sec.)

3. The seasoning process is confirmed by switching the

light OFF twice and then back ON again.

4. Now turn all controls to the chosen settings.

5. The light is now left ON for 100 hours without sensor

function. Do not disconnect the light from the mains

power supply during this period.

6. After 100 hours, the light automatically switches to

the sensor mode previously selected in step 4.

Note:

When fluorescent tubes are new or at low ambient

temperatures, the sensor may not switch the light OFF

as it might be detecting gas moving inside the tubes. In

this case, switch the light OFF and, for the time being,

drastically reduce the reach setting.

Removing base



Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel FRS 30 in the language / languages: All languages as an attachment in your email.

The manual is 3,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel FRS 30 Manual

Product: