Manual Steel Cucine GP6B-4 (page 13 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

651795

Zoom out

Zoom in

1/52

INSTRUCTIONS FOR THE INSTALLER

Gas connection

Make sure that the appliance is adjusted for

the gas type available (see the label under the

appliance). Follow the instructions indicated in the

chapter “gas transformations and adjustments” for

the possible adaptation to different gases.

The appliance must be connected to the gas

system by means of stiff metal pipes or flexible

steel pipes having continuous walls, in compliance

with the regulations in force.

Some models are equipped with both cylindrical

A and conical B connectors for gas supply (fig. 7).

Please select the type which is correct for the

supply concerned.

The connection must not stress the gas ramp.

Once the installation is over, check the

connection seal with a soapy solution.

Electric connection

The connection to the electric grid must be carried

out by qualified personnel and in conformity with

the regulations in force.

The voltage of the electric system must correspond

to the value indicated in the label under the

appliance. Make sure that the electric system is

provided with an effective ground connction in

compliance with the regulations and provisions of

the law. Grounding is compulsory.

GAS TRANSFORMATIONS AND ADJUSTMENTS

Replacing the nozzles

If the equipment is adjusted for a type of gas that is

different from the one available, it is necessary to

replace the burner nozzles.

The choice of the nozzles to replace must be

made according to the table of the “technical

characteristics” as enclosed.

Act as follows:

- Remove the racks and burners.

- By means of a straight spanner L, unscrew the

nozzle U (fig.8-8/A) and substitute it with the

corresponding one.

- Tighten the nozzle strongly.

- Cover the label control regulation placed under

the hobs with the one contained in the envelope

spare nozzles.

Adjusting the burners

The lowest flame point must always be properly

adjusted and the flame must remain on even if

there is an abrupt shift from the maximum to the

minimum position.

If this is not so, it is necessary to adjust the lowest

flame point as follows:

- start the burner up;

- turn the tap up to the minimum position (small

flame);

- remove the knob from the tap rod;

- introduce a flat-tip screwdriver in the hole F of

the tap (fig.9) and turn the by-pass screw up to a

proper adjustment of the lowest flame point.

As regards G30 gas burners, the by-pass screw

must be tightened completely.

MAINTENANCE

Replacing the power supply cable

If the power supply cable should be replaced,

it is necessary to use a cable with a section of

3x0.75mm

, type H05VV-F or H05RR-F, complying

with the regulations in force.

The connection to the terminal board must be

effected as shown in fig.10:

brown cable L (phase)

blue cable N (neutral)

green-yellow cable (ground)

The manufacturing firm refuses all responsibility for any possible imprecision in this booklet, due to misprints or

clerical errors. It reserves the right to make all the changes that it will consider necessary in its own products,

without effecting the essential characteristics of functionality and safety.

This product complies with EU Directive 2002/96/EC.

The crossed-out dustbin symbol reported on the appliance indicates that the appliance must be

disposed of separately from other domestic refuse at the end of its useful life. It must therefore be

delivered to a waste recycling centre specifically for electric and electronic equipment or returned

to the retailer at the moment of purchase of a new equivalent appliance.

The user is responsible for delivering the appliance to the appropriate collection centre at the end of its useful

life, Failure to do so may result in a fine, as provided for by laws governing waste disposal. Differential collection

of waste products for eventual recycling, treatment and environmentally friendly disposal helps reduce possible

negative effects on the environment and health, and also enables the materials making up the product to be

recycled. For more detailed information on the available refuse collection systems, refer to the local Municipal

Solid Waste disposal centre or the shop where the product was purchased. Producers and importers are

responsible for fulfilling their obligations as regards recycling, treatment and environmentally friendly disposal by

directly or indirectly participating in the collection system.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steel Cucine GP6B-4 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steel Cucine GP6B-4 Manual

Product: