ENGLISH
DIRECTIONS FOR USE
1. For your own safety
This fan heater is an extra-heating in the house. It must be used according to this concept.
Make sure that your supply rating corresponds to what specified on the rating plate i.e. 230 V AC,
50 Hz.
Don't leave your home while the appliance is in function: ensure in this case that the switch is in
OFF (0) position and the thermostat is in minimum position “”.
During function, place the heater in a safe position :
- far (1 mt. ) from inflammable objects or furnitures;
- leaving the air outlet space free : 1 mt. of free space in front of the heater and 50 cm. of free
space behind it;
- not located immediately below a socket-outlet.
Do not leave animals or children touch or play with the appliance. Pay attention! The air outlet
grille gets hot during operation (more
than 80°C i.e. 175°F)
WARNING: In order to avoid overheating, do not cover the heater. Do not hang anything on
the heater and do not cover it while it’s working. This is clearly written on the cover of the product
or shown by the symbol
OR
Do not use the heater in rooms with explosive gas or while using inflammable solvents or varnish
or glues.
If the cordset is damaged and you have to change it, do not do the job yourselves! Take the
product to an after sales authorised repair centre or to a person with similar skill and knowledge,
in order to avoid any risk of danger.
Do not use this heater close to showers, baths, swimming pools.
The appliance must be positioned so that the plug is always accessible.
The appliance shall not be used directly under a wall socket
2. Safe positioning
Use the appliance only in upright position.
As the fan heater is in class 2, earth connection is not required.
This appliance has a drip proof moisture resistance IP X1. It can therefore be used in bathrooms,
provided you keep at least 60 cm. distance from the edge of the bath or the shower or the water
basin. Never use the heater in the areas marked in grey in the following
drawing
Also it shouldn't be possible to touch the knobs by a person in the bath or in the shower.
3. Cord storage
For product recovery you can store the cordset pressing it into the product.
Mind that during function the cordset must be always completely pulled out.
4. Use of the heater
Version just with switch
The heater has 1 knob controllling the switch.
The switch knob has 5 positions, allowing to select the desired power setting :
= COLD AIR: only the fan works
O
= OFF
= WARM AIR at reduced motor speed (QUIET MODE)
= WARM AIR at full motor speed
= HOT AIR at full motor speed
Turn the switch knob to select the desired power setting
Version just with thermostat
Starting from the “” position, turn the thermostat knob clockwise until you hear a "click»: the
appliance starts working at 2000W.
The thermostat maintains the desired room temperature switching on and off automatically the
appliance. The more the knob is turned clockwise, the higher is the maintained temperature.
Maximum thermostat setting corresponds at about 30°C; “” position corresponds to
ap
proximately 5°C.
Use of the thermostat
In a room where the temperature is too high (more than 30°C), it is normal that the thermostat will
not switch on the heater.
In a room where the temperature is too low (around 5°C or even less) it is also normal that the
thermostat will keep the appliance working until the temperature gets higher.
To select the right thermostat position we suggest you to
-
turn the thermostat in maximum position (clockwise);
-
leave the appliance working until the comfortable temperature is reached;
-
turn the knob anti clockwise until you hear a "click" and the appliance stops;
-
turn clockwise again the knob (just a little): in this position the thermostat will maintain the
comfortable temperature you have selected.
Version with switch and thermostat
The heater has 2 knos controllling the switch and the thermostat.
The switch knob has 5 positions, allowing to select the desired power setting :
= COLD AIR: only the fan works
2,53m
0,6m
0,6m
