619140
45
Zoom out
Zoom in
Previous page
1/52
Next page
45
Item
Lowest
Value
Highest
Value
Default
Value Meaning
MNS 0.3 (mi)
0.8 (k)
2.0 (mi)
3.2 (k)
0.5 (mi)
0.8 (k)
Minimum Speed. Treadmill minimum operating speed in miles or kilometers,
based on current UNx setting.
MXS 5.0 (mi)
5.0 (k)
12.5 (mi)
20.0 (k)
5.0 (mi)
5.0 (k)
Maximum Speed. Treadmill maximum operating speed in miles or kilometers,
based on current UNx setting.
ACC 25 60 25 Acceleration Time. Time in seconds to accelerate from current speed to a
specified higher speed.
DEC 20 60 20 Deceleration Time. Time in seconds to decelerate from current speed to a
specified lower speed.
AST OFF ON OFF Auto Stop Enable. Enables/disables Auto Stop function.
AFE OFF ON ON Auto Fan Enable. Enables/disables Auto Fan function.
PAU 30 120 60 Pause duration during a program, in seconds, either 30, 45, 60, 90 or 120.
MAINTENANCE MODE
Your Service Representative may need to check accumulated data about the past usage of your treadmill, test its display
controls, or investigate error messages. For these reasons, your treadmill is equipped with a Maintenance Mode. The
Maintenance Mode includes all of the items available through Manager Mode, plus additional items for Service and Diagnostic
use. To enter Maintenance Mode:
1. Press and hold the
, and keys together.
2. A beep will sound and “MAINTENANCE SETTINGS” will scroll once across the P
ROFILE Window.
3. Release all keys. “SN” will display in the PROFILE Window; the associated numeric value for the parameter will
display in the DISTANCE Window.
NOTE: The system will automatically exit MAINTENANCE SETTINGS if no key is pressed for 30 seconds.
The following keys are used to modify MANAGER SETTINGS:
Increase and Decrease Incline Keys: Display the next (Increase) and previous (Decrease) parameters.
Keys will repeat if held.
Numeric Keypad: Facilitates entry of the desired value for the displayed parameter. These keys do not save
the new value – see OK Key below.
OK Key: Updates (saves) the value of the displayed parameter in Flash memory. “UPDATING” will scroll
once across the P
ROFILE Window while the update is in process. When the update is complete, the PROFILE
Window will show the new value for the parameter.
NOTE: To exit Maintenance Mode without saving any values or settings, press the S
TOP key.
NOTE: Unless otherwise specified, the Item (parameter) name is shown in the PROFILE Window, and the value of the
parameter is shown in the D
ISTANCE Window.
The items that you may display and change with the previous keys are:
Item
Lowest
Value
Highest
Value
Default
Value Meaning
SN 0 9999 N/A Serial Number. S Series Treadmill serial number (set by factory).
DSW 1.0 99.99 N/A Display Software. Display panel software version number (set by factory).
NOTE: Software checksum value is displayed in C
ALORIES Window; software
Build value is displayed in T
IME Window
OHR 0 9999 0 Operating Hours. Total operating hours.
DST 0 9999 0 Distance. Total distance traveled in miles or kilometers, based on current UNx
setting.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for StarTrac S-TRc Treadmill at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of StarTrac S-TRc Treadmill in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info