781907
16
Zoom out
Zoom in
Previous page
1/24
Next page
16
Before start-up
Replace cracked diamond cutting discs.
Get to know your machine. Familiarize yourself with
its use and its restrictions, but also with the specic
potential risks.
Check the machine carefully for damages to ensure
that it is able to achieve the intended output. In case
of doubt, please replace the concerned component.
Ensure that the switch is on Off, before inserting the
power plug into the mains socket.
Ensure that the machine is cleaned and lubricated
properly.
Before start-up, check the machine for damaged parts
and nd out whether these parts are working properly
and performing their dened function.
Check the alignment of all moving parts, all broken
or fastening parts, and all other conditions that can
affect smooth operation. Each damaged part should
be repaired or replaced by a technician immediately.
Do not use the machine if a switch cannot be activat-
ed/deactivated correctly.
Operation
Install the machine on an even, slide-proof oor.
Check that the voltage on the nameplate matches the
existing voltage; connect the power plug to the mains
power supply only thereafter
The cutting disc should be free to run before the ma-
chine is switched on.
Caution: Cutting disc must always be cooled with water.
Caution: Cutting disc runs with a time lag.
Do not break the cutting disc by applying pressure at the
sides.
Under normal use conditions, the motor casing can
become hot.
Do not use force on the machine or on an accessory
to achieve the performance of a bigger Industrial ma-
chine. It does a better job at the output for which it is
designed.
Dene all machine settings only when it is switched
off.
Do not leave the machine unattended as long as it
is running.
During shutdown, leave the machine only after it
comes to a complete standstill.
Always switch the machine off before pulling out the
power plug from the mains socket.
Always pull out the power plug. Never disconnect the
power plug from the mains socket by pulling at the
cable.
Do not use cutting discs that do not meet the size
specications.
Do not carry the machine by the cable.
Do not work with the machine if you are not sure whether
a working condition is safe of unsafe.
EQUIPMENT FIG.1-2
1 Machine head
2 Base frame
3 Legs
4 Water tub
5 Workpiece support
6 Transverse cutting gauge
7 Angled stop
8 Guide rails
9 Cutting disc protection
10 Diamond cutting-disc
11 Handle
12 Star knob screw for angle adjustment
13 Cooling water pump
14 Hose
15 Motor
16 ON/OFF switch
17 Angle scale
18 Table extension
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Starkwerk SW 4700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Starkwerk SW 4700 in the language / languages: English, German as an attachment in your email.

The manual is 4.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info