622316
17
Zoom out
Zoom in
Previous page
1/22
Next page
14
Appendix
Stanley TLM 220i 773938a en
EN
D
F
I
E
P
NL
N
S
DK
FIN
RUS
PL
GR
H
CZ
SK
LT
EST
LV
RO
BG
Long range Mode ( )
Press the key. The symbol is displayed.
Unfavourable conditions (strong sunlight or a very weak reflective target
surface) may reduce the range of the device, in spite of this the long range
mode allows you to take measurements over longer distances. The use of
a tripod and measurement initiation by pressing the key are recom-
mended when measurements over 30m are made over longer time periods
in these conditions. (For details see Technical specifications)
)
The settings are reset when the device is switched off.
Timer (self-triggering)
Press this button to set a 5-second time delay.
or
Press and hold down this button until the desired time delay is
reached (max. 60 seconds).
Once the key is released with the laser activated, the remaining seconds
until measurement (e.g. 59, 58, 57...) are displayed in a countdown. The last
5 seconds are counted down with a beep. After the last beep the measu-
rement is taken and the value is displayed.
)
The timer can be used for all measurements.
Appendix
Message codes
All message codes are displayed with either or "Error". The following
errors can be corrected:
Cause Remedy
156
Transverse tilt greater than 10° Hold the instrument without
any transverse tilt
160
Main tilt direction, angle too
high (> 45°)
Measure angle up to max. ± 45°
162
The calibration has not been
accomplished on a leveled
surface and the calibration value
is respecitvely within an ineli-
gible area.
Calibrate the device on an abso-
lute horizontal leveled surface.
204
Calculation error Repeat procedure
252
Temperature too high Cool down instrument
253
Temperature too low Warm up instrument
255
Receiver signal too weak,
measurement time too long,
distance > 100 m
Use target plate
256
Received signal too strong Target too reflective (use target
plate)
257
Wrong measurement, back-
ground brightness too high
Darken target (measure in diffe-
rent lighting conditions)
260
Laser beam interrupted Repeat measurement
Error Cause Remedy
Error Hardware error Switch on/off the device several
times. If the symbol still appears,
then your instrument is defec-
tive. Please call your dealer for
assistance.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley TLM220i - 77.116 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley TLM220i - 77.116 in the language / languages: English as an attachment in your email.

The manual is 3,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stanley TLM220i - 77.116

Stanley TLM220i - 77.116 User Manual - German - 22 pages

Stanley TLM220i - 77.116 User Manual - Dutch - 22 pages

Stanley TLM220i - 77.116 User Manual - French - 22 pages

Stanley TLM220i - 77.116 User Manual - Spanish - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info