720680
4
Zoom out
Zoom in
Previous page
1/8
Next page
ENGLISH
4
(Original instructions)
h. Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Before drilling into walls, floors or ceilings check for the
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
Additional Safety Instructions for Heat Guns
1) A fire may result if the appliance is not used with care,
therefore
- Do not apply to the same place for long time
- Do not sue in presence of an explosive atmosphere
- Be aware that heat may be conducted to combustible
materials that are out of sight
- Place the appliance on site after use and allow it to
cool down before storage
- Do not leave the appliance unattended when it
is switched on.
Always switch off before putting tool down.
Extreme care should be taken when stripping paint,
the peelings, residue and vapors of paint may contain
lead, which is poisonous. Once deposited on surfaces,
hand to mouth contact can result in the ingestion of lead.
Exposures to even low levels of lead can caused
irreversible brain and nervous system damage; young
and unborn children are particularly vulnerable. Do not
smoke, eat or drink in a work area that could or may be
contaminated by lead. Lead based paints should only
be removed by a professional and should not be
removed using a heat gun.
When removing paints you should ensure that your
work area is enclosed. It is advisable to wear a dust
mask.
Do not burn the paint. Keep the nozzle at least 25mm
(1”) from the surface as this keeps the temperature
below the required 450°C. If you are scraping from a
vertical position then you should scrape downwards to
prevent the paint from falling back into the heat gun and
burning. Dispose of all paint debris safely and ensure
that the work area is thoroughly cleaned after completing
the job.
Do not use in a damp atmosphere or where
flammable gases may be present or use near
combustible materials. Spaces behind boards, ceilings
and floors and wall cavities in timber frame constructed
houses can contain flammable materials. Check before
using the heat gun.
Allow the tool to cool fully before storing.
Ensure adequate ventilation when using heat guns as
toxic fumes may be produced.
Do not use as a hairdryer! The air temperature is far
higher than a hairdryer.
Do not obstruct either the air intake or nozzle outlet as
this may cause excessive heat build up resulting in
damage to the tool.
Do not direct the hot air blast at other people.
Do not touch the metal nozzle as it becomes very hot
during use and remains hot for up to 30 minutes after
use. Do not look down the nozzle while the unit is
working because of the high temperatures being
produced.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley SXH1800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley SXH1800 in the language / languages: English as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info