Manual Stanley STSP125 (page 7 of 56) (English, French, Portuguese)

720790

Zoom out

Zoom in

1/56

ENGLISH

(Original instructions)

7. Electrical Safety

Your tool is double insulated; therefore no earth

wire is required. Always check that the main

voltage corresponds to the voltage on the rating plate.

Warning! If the power cord is damaged, it must

be replaced by the manufacturer, authorized

STANLEY Service Center or an equally qualiﬁed

person in order to avoid damage or injury. If the power cord

is replaced by an equally qualiﬁed person, but not

authorized by STANLEY, the warranty will not be valid.

Using an Extension Cable

An extension cable should not be used unless absolutely

necessary. Use of an improper extension cable could result

in a risk of ﬁre and electric shock. If an extension cable must

be used, use only those that are approved by the country’s

electrical authority. Make sure that the extension cable is in

good condition before using. Always use the cable that is

suitable for the power input of your tool (see technical data

on name plate). The minimum conductor size is 1.5mm

Feature (Fig. A)

1. On/Off switch

2. Lock-on button

3. Butterﬂy screw

4. Base

5. Brush cap

6. Socket wrench

7. Spanner

Assembly And Adjustment

Warning! Prior to assembly and adjustment,

always unplug the tool.

Installing and removing the diamond wheel (Fig. C)

• Insert the diamond wheel (9) to the spindle.

• Grip outside ﬂange with spanner (7) and turn the screw

counterclockwise with the socket wrench (6).

• Be sure to tighten clamp blot securely.

• Use only the recommended diamond wheel with the

correct hole size.

• Removing

• Follow the procedures above in reverse order.

Cutting depth adjustment (Fig. D)

• To increase or decrease the depth of cut, loosen the

butterﬂy screw (3), move the base (4) to adjust the depth,

and tighten the screw to secure the depth.

• To prevent tool fault, the depth-of-cut adjustment knob

has been set to the optimal position at factory default.

Note: Users may also set the knob to a desired position at

any time.

Use

Warning! Always observe the safety instructions

and applicable regulations.

Warning! Ensure that the butterﬂy screw (3) is

properly tightened before operating the tool.

Switching On And Off (Fig. B)

• To switch the tool on, press the on/off switch (1).

• To switch the tool off, release the on/off switch (1).

• This tool has a lock-on feature. To activate, press the

on/off switch and then the lock-on button (2). To

de-activate, press the on/off button again.

Read

Instructions

Manual

Use Eye

Protection

Use Ear

Protection

V ........ Volts

A ........ Amperes

Hz ....... Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

....... No-Load

Sp eed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Recipro-

cation per

minute

6. Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of

manufacture, is printed into the housing.

Example:

2014 XX JN

Year of manufacturing

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STSP125 in the language / languages: English, French, Portuguese as an attachment in your email.

The manual is 4,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley STSP125 Manual

Product: