720789
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
Maintenance
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of
maintenance.Continuous satisfactory operation depends
upon proper tool care and regular cleaning.Your tool is not
user-serviceable. Take the tool to an authorized STANLEY
repair agent. This tool should be serviced at regular
intervals or when showing a noticeable change in
performance.
Lubrication
STANLEY power tools are properly lubricated at the factory
and are ready for use. Tools should be re-lubricated
regularly , depending on usage. This lubrication should only
be attempted by trained power tool repair persons, such as
those at STANLEY service centers or by other qualified
service personnel. Closed-type, grease-sealed ball bearings
are used throughout. These bearings have sufficient
lubricationpacked in them at the factory to last the life of the
chop saw.
Cleaning
Warning: unplug the tool before you use a cloth
to clean the housing.With the motor running,
blow dirt and dust out of all air vents with dry air
at least once a week. Wear safety glasses when performing
this. Exterior plastic parts may be cleaned with a damp cloth
and mild detergent. Although these parts are highly solvent
resistant, NEVER use solvents.
Blowing dust and grit out of the main housing by means of
an air hose is recommended and may be done as often as
dirt is seen collecting in and around the air vents. Always
wear proper eye and respiratory protection.
Tool care
Avoid overloading the machine.Overloading will result in a
considerable reduction in speed and efficiency and the unit
will become hot. In this event,run the machine at no load for
a minute or two until cooled to normal working temperature
by the built in fan. Switching your machine on and off whilst
under load will considerably reduce the life of the switch.
Important
To ensure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (other than those listed in this
manual) should be performed by authorized service centers
or other qualified organizations, always-using identical
replacement parts. Unit contains no user serviceable parts
inside.Blowing dust and grit out of the main housing by
means of an air hose is recommended and may be done as
often as dirt is seen collecting in and around the air vents.
Always wear proper eye and respiratory protection.
Note: Unit may be converted to a 3-wire twist lock cord set
at an authorized service center.
Notes
STANLEY's policy is one of continuous improvement to
our products and, as such, we reserve the right
tochange product specifications without prior notice.
Standard equipment and accessories may vary by
country.
Product specifications may differ by country.
Complete product range may not be available in all
countries.
Contact your local STANLEY dealers for range
availability.
ENGLISH (Original instructions)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STSC2135 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STSC2135 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info