Manual Stanley STSC1518 (page 10 of 14) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

720697

Zoom out

Zoom in

1/14

ENGLISH

(Original instructions)

• Loosen and remove the blade retaining screw (11) by

turning it counterclockwise using the hex wrench (15).

• Remove the outer washer (10).

• Remove the saw blade (5). Warning! To reduce the risk

of serious personal injury, read, understand and follow

all important safety warnings and instructions prior to

using tool.

General Cuts

Guard against kickback

With unit unplugged, follow all assembly, adjustment and set

up instructions. Make sure lower guard operates. Select the

proper blade for the material to be cut.

• Measure and mark work for cutting.

• Support and secure work properly (See Safety Rules

and Instructions).

• Use appropriate and required safety equipment (See

Safety Rules).

• Secure and maintain work area (See Safety Rules).

• With plug inserted and guard closed, make sure switch

turns saw on and off.

Warning! It is important to support the work

properly and to hold the saw ﬁrmly to prevent loss

of control which could cause personal injury. Fig.

C illustrates recommended hand position.

Operation

Switch

• To operate the tool, depress the trigger switch (1). The

tool will continue to run as long as the trigger is

depressed.

• To turn the tool off, release the trigger switch (1). There

is no provision for locking the tool on, and the switch

should never be locked on by any other means.

Sawing

Warning! To reduce the risk of serious personal

injury,always hold the tool with both hands.

• Let the blade run freely for a few seconds before starting

the cut.

• Apply only a gentle pressure to the tool while performing

the cut.

• Work with the shoe pressed against the workpiece.

Hints For Optimum Use

• As some splintering along the line of cut on the top side

of the workpiece cannot be avoided, cut on the side

where splintering is acceptable.

• Where splintering is to be minimized, e.g. when cutting

laminates, clamp a piece of plywood onto the top of the

workpiece.

Pocket cutting (Fig. K)

Pocket cutting is used to cut a hole in a piece of material

without cutting from the side.

• Measure and mark work.

• Tilt saw forward and rest front of the shoe on material to

be cut. Align so that cut will begin at the back of the

drawn rectangle shown in Fig. K.

• Using the retracting lever, retract blade guard to an

upward position, with the blade just clearing the material,

start motor and gradually lower the saw into the material.

Warning! As blade starts cutting the material,

release the retracting lever immediately.

• Never tie the blade guard in a raised position.

• When the shoe rests ﬂat on the material being cut,

complete the cut in forward direction.

• Allow the blade to come to a complete stop before lifting

saw from material.

• When starting each new cut, repeat the above steps

Wrench storage (Fig. L)

The spanner wrench (8) can be stored on the saw shoe as

shown in Fig. L.

Attaching and removing the rip fence (Fig. M)

The rip fence is used to saw in a straight line parallel to the

edge of the working piece.

Attaching

• Loosen the locking knob (17).

• Insert the rip fence (18) through the openings (19).

• Slide the rip fence into the desired position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STSC1518 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley STSC1518 Manual

Product: