720752

Stanley STHT77498-1 Manual

11
Zoom out
Zoom in
Previous page
1/226
Next page
11
GB
4.
Mark
a
on the center of the beam on the wall.
5.
Turn the laser 90º clockwise so that the left-most
end of the laser line is displayed near
a
(Figure
D
2
).
6.
Mark
b
on the center of the beam on the wall.
7.
Measure the vertical distance between
a
and
b
.
8.
If your measurement is greater than the
Allowable Distance Between
a
and
b
for the
corresponding Distance Between Walls in the
following table, the laser must be serviced at an
authorized service center.
Distance
Between Walls
Allowable Distance
Between
a
and
b
30′ (9m) 15/32” (12mm)
40′ (12m) 9/16” (14.4mm)
50′ (15m) 23/32” (18mm)
Horizontal Beam - Pitch Direction
Checking the horizontal pitch calibration of the
laser requires a single wall at least 30′ (9m) long.
It is important to conduct a calibration check using
a distance no shorter than the distance of the
applications for which the tool will be used.
1.
Place the laser against the end of the wall
(Figure
E
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
At least 30′ (9m) apart along the laser beam,
mark
a
and
b
.
4.
Move the laser to the opposite end of the wall
(Figure
E
2
).
5.
Position the laser toward the rst end of the same
wall and parallel to the adjacent wall.
6.
Adjust the height of the laser so the center of the
beam is aligned with
b
.
7.
Directly above or below
a
, mark
c
along the
laser beam (Figure
E
3
).
8.
Measure the distance between
a
and
c
.
9.
If your measurement is greater than the
Allowable Distance Between
a
and
c
for the
corresponding Distance Between
a
and
b
in
the following table, the laser must be serviced at
an authorized service center.
Distance Between
a
and
b
Allowable Distance
Between
a
and
c
30′ (9m) 15/32” (12mm)
40′ (12m) 9/16” (14.4mm)
50′ (15m) 23/32” (18mm)
Vertical Beam - Plumb
Checking the vertical (plumb) calibration of the
laser can be most accurately done when there is
a substantial amount of vertical height available,
ideally 30′ (9m), with one person on the oor
positioning the laser and another person near a ceiling
to mark the position of the beam. It is important to
conduct a calibration check using a distance no
shorter than the distance of the applications for which
the tool will be used.
1.
On the oor between two walls, mark a 5 ft.
(1.5 m) line that is parallel to the adjacent wall
(Figure
F
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
Place the laser at one end of the line on the oor,
making sure the vertical laser beam is aligned
and centered on the line.
4.
Where the vertical laser beam appears on the
ceiling, mark
a
. (This should be directly over the
midpoint of the line on the oor.)
5.
Move the laser to the other end of the line on the
oor (Figure
F
2
).
6.
Where the vertical laser beam appears on the
ceiling, mark
b
, directly beside the rst mark
a
.
7.
Measure the distance between
a
and
b
.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT77498-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT77498-1 in the language / languages: All languages as an attachment in your email.

The manual is 5,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info