720835
2
Zoom out
Zoom in
Previous page
1/208
Next page
2
User Manual
GB
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
2000
k
200k
20k
2000
200
200
m
20m
2000
μ
200
μ
200
200
20
2000
m
200
m
300300
10
Test Leads
Highest Value
10 A
Terminal
Function/
Range
Switch
Data Hold
Button
COM
Terminal
Terminal
Display
Low
Battery
Reading
K Type Thermocouple
STANLEY
®
Multimeter
The STANLEY Multimeter is a CAT III
300 V 10 A compact digital multimeter for
measuring DC and AC voltage, DC current,
resistance, continuity, diode polarity, and
temperature. It features polarity indication, data
hold, and overrange indication.
User Safety
WARNING: Read and understand all
instructions before using product.
Failure to follow all instructions may result in
severe injury or death:
CAT III – This measurement Category III
multimeter is for use on permanently installed
loads. Examples are measurements on
distribution boards, circuit breakers, wiring,
and equipment like xed installation motors.
Do not use the meter for measurements
higher than Category III 300 V 10 A.
DO NOT use the meter if it is damaged.
Before using the meter, inspect the case.
Pay particular attention to the insulation
surrounding the connectors.
ALWAYS Inspect the test leads for damaged
insulation or exposed metal. Check the test
leads for continuity. Replace damaged test
leads before you use the meter.
DO NOT use the meter if it operates
abnormally. Protection may be impaired.
DO NOT operate the meter where explosive
gas, vapor, or dust is present.
DO NOT apply more than the rated voltage,
as marked on the meter, between terminals or
between any terminal and earth ground.
ALWAYS verify the meter’s operation by
measuring a known voltage before use.
ALWAYS turn off circuit power before
connecting the meter in the circuit to measure
current. Remember to place the meter in
series with the circuit.
ALWAYS turn off circuit power before
connecting the meter to the circuit to measure
resistance.
ALWAYS Use caution when working with
voltage above 30 V AC rms, 42 V peak, or
60 V DC. These voltages pose an increased
shock hazard.
ALWAYS keep your ngers behind the nger
guards on the probes when in use.
ALWAYS connect the common test lead
before you connect the live test lead. When
you disconnect test leads, disconnect the live
test lead rst.
ALWAYS Remove the test leads from the
meter before you open the battery cover or the
case.
DO NOT operate the meter with the battery
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT0-77364 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT0-77364 in the language / languages: All languages as an attachment in your email.

The manual is 29,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info