720460
6
Zoom out
Zoom in
Previous page
1/10
Next page
6
ENGLISH
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised STANLEY Service Centre
in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse switch
4. Drilling mode selector
5. Tool holder
6. Side handle
7. Depth stop
8. Depth stop lock button
Assembly
Warning! Before assembly, make sure that the tool
is switched off and unplugged.
Fitting the side handle
Turn the grip counterclockwise until you can slide the
side handle (6) onto the front of the tool.
Rotate the side handle into the desired position.
Tighten the side handle by turning the grip clockwise.
Fitting an accessory (fig. A)
Clean and grease the shank (9) of the accessory.
Pull back the sleeve (10) and insert the shank into the
tool holder (5).
Push the accessory down and turn it slightly until it fits
into the slots.
Pull on the accessory to check if it is properly locked.
The hammering function requires the accessory to be
able to move axially several centimetres when locked in
the tool holder.
To remove the accessory, pull back the sleeve (10) and
pull out the accessory.
Use
Wear a dust mask
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes
Selecting the operating mode (fig. B)
The tool can be used in three operating modes. Press in the
button (11) and rotate the drilling mode selector (4) towards
the required position, as indicated by the symbols.
Drilling
For drilling in steel, wood and plastics, set the operating
mode selector (4) to the position.
Hammer drilling
For hammer drilling in masonry and concrete, set the
operating mode selector (4) to the position
When hammering, the tool should not bounce and run
smoothly. If necessary, increase the speed.
(Original instructions)
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
Labels on tool
The label on your tool may include the following symbols:
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHR263 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHR263 in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info