720457
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
ENGLISH
(Original instructions)
These are:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised STANLEY Service Centre
in order to avoid a hazard.
Using an extension cable
If it is necessary to use an extension cable, please used an
approved extension cable that fits the tool’s power input
specifications (please refer to the technical data). The
minimum cross-sectional area of the conducting wire is 1.5
sq. mm. Cables should be untangled before reeling up.
Features
This tool includes some or all of the following features.
a. Side Handle
b. Switch
c. Barrel cover
d. Tool sleeve
e. Lube oil-injection inlet
Assembly and adjustment
Warning! To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing
accessories, before adjusting or changing set-ups or when
making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
Inserting and removing SDS Max accessories (fig. 1)
This tool uses SDS Max accessories (refer to the inset in
figure 1 for a cross-section of an SDS Max bit shank). We
recommend to use professional accessories only.
1. Clean and grease the bit shank.
2. Insert the bit shank into the bit holder/tool sleeve (d).
3. Push the bit down and turn it slightly until it fits into the
slots.
4. Pull on the bit to check if it is properly locked. The
hammering function requires the bit to be able to move
axially several centimetres when locked in the tool
holder.
5. To remove a bit pull back the tool holder/locking sleeve
(d) and pull out the bit.
Warning: Always wear gloves when you change
accessories. The exposed metal parts on the
tool and accessory may become extremly hot
during operation.
Fitting the side handle (fig. 1)
The side handle (a) can be fitted to suit both RH- and
LH-users.
Warning: Do not use the tool without the side
handle properly assembled.
1. Loosen the side handle.
2. For RH-users: Slide the side handle clamp over the
collar behind the tool holder, handle at the left. For
LH-users: Slide the side handle clamp over the collar
behind the tool holder, handle at the right.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
Labels on tool
The label on your tool may include the following symbols:
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHM5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHM5 in the language / languages: English as an attachment in your email.

The manual is 1,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info