720767

Stanley STGS6115 Manual

9
Zoom out
Zoom in
Previous page
1/32
Next page
Attaching the Guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (c) collar over the groove (i)
of the gear housing.
3. Turn the guard (c) counterclockwise by 150 degrees.
4. Make sure that the screws (k) are tightened.
Removing the Guard
1. Loosen the screws (k) on the guard collar.
2. Pull up the guard (c).
Warning: Do not operate the tool when the
safety guard is not in place.
Note: Refer to the grinding accessories chart at the end of
this section for accessories that can be used together with
this angle grinder.
Attaching and Removing Grinding Wheels
(Fig. 3, 4)
Warning: Do not use damaged grinding wheels.
1. Place the tool on a work bench, groove facing up.
2. Attach the inner flange (d) correctly on the output shaft
(e) (Fig. 3).
3. Place the grinding wheel (f) on the inner flange (d).
When attaching a grinding wheel with a raised center,
make sure that the raised center (g) faces the inner
flange (d).
4. Tighten the outer flange (h) until the output shaft (e) (Fig.
4). When attaching the grinding wheel, the ring on top of
the outer flange (h) must face the wheel.
5. Press the spindle lock (b) and prevent the spindle (e)
from rotating until it locks in place.
6. Use the pin spanner to tighten the outer flange (h).
Preparation Before Use
• Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
• Make sure that the inner and outer flanges are attached
correctly.
• Make sure that the abrasive or grinding wheels are
rotating in the direction of the arrows on the accessories
and tool.
Operation (Fig. 5)
Instructions
Warning: Always observe the safety instructions
and applicable regulations.
Warning: To minimize the danger of serious
personal injury, please switch off the tool power
and disconnect all plugs before adjusting or
removing/installing any accessory. Before reassembling the
tool, press and release the trigger switch to make sure the
tool is already switched off.
Warning:
• Make sure all materials to be grinded are secured in
position.
• Apply slight pressure to the tool. Do not apply side
pressure to the abrasive disc.
• Avoid overloading. If the tool becomes hot, let it spin for
a few minutes with no load.
1. Be sure to hold the tool tightly with both hands (one hand
on housing, the other on side handle). Start the tool and
bring the grinding wheel on the workpiece.
9
(Original instructions) ENGLISH
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STGS6115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STGS6115 in the language / languages: English, French as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info