Manual Stanley STGL2223 (page 9 of 28) (English, French)

720778

Zoom out

Zoom in

1/28

ENGLISH

(Original instructions)

PACKAGE CONTENTS

1 Angle grinder

1 Guard

1 Side handle

1 Flange set

1 Two-pin spanner

1 Instruction manual

• Check for damage to the tool, parts or accessories which

may have occurred during transport.

• Take the time to thoroughly read and understand this

manual prior to operation.

FEATURES (Fig A)

This appliance includes some or all of the following features.

WARNING: Never modify the power tool or any part

of it. Damage or personal injury could result.

1. Switch

2. Spindle lock

3. Guard

4. Side handle

Purpose of design

This angle grinder is designed especially for grinding.

Do not use sandpaper discs and grinding wheels other than

those with depressed center.

Do not use the tool in wet conditions or environments in the

presence of ﬂammable liquids or gases.

This angle grinder is a professional power tool.

Do not allow children to come in contact with this tool.

Inexperienced operators are required to use this tool under

supervision.

ASSEMBLY

WARNING: To minimize the danger of serious

personal injury, please switch off the tool power

and disconnect all plugs before adjusting or

removing/installing any accessory. Before

reassembling the tool, press and release the trigger

switch to make sure the tool is already switched off.

Attaching and removing the wheel guard (Fig. B)

WARNING To minimize the danger of serious

personal injury, please switch off the tool power

and disconnect all plugs before adjusting or

removing/installing any accessory. Before

reassembling the tool, press and release the trigger

switch to make sure the tool is already switched off.

Attaching the guard

1. Place the angle grinder on a work bench, groove facing

up.

2. Bring the ﬂange of the guard (3) collar over the groove of

the gear housing.

3. Turn the guard (3) counterclockwise by 150 degrees.

4. Make sure that the screws (12) are tightened.

Removing the guard

1. Loosen the screws (12) on the guard collar.

2. Pull up the guard (3).

WARNING: Do not operate the tool when the safety

guard is not in place.

Fitting and removing a grinding wheel (Fig C1, C2, C3)

WARNING: Do not use damaged grinding wheels.

1. Place the tool on a work bench, guard up.

2. Fit the inner ﬂange (5) correctly onto the spindle (6)

(Fig. C1).

3. Place the disc (7) on the ﬂange (5) (Fig.C2). When ﬁtting a

disc with a raised center, make sure that the raised centre

(8) is facing the ﬂange (5).

4. Screw the out ﬂange (9) onto the spindle (6) (Fig. C3)

- the ring on the ﬂange (9) must face towards the disc

when ﬁtting a grinding disc (C3-A)

- the ring on the ﬂange (9) must face away from the

disc when ﬁtting a cutting disc (C3-B)

LABELS ON TOOL

The label on your tool may include the following symbols:

Position of date code

The date code, which also includes the year of manufacture,

is printed into the housing.

Example:

2017 XX JN

Year of manufacturing

WARNING! To reduce the risk of injury, the user

must read the instruction manual before use.

Wear ear protection.

Wear a dust mask.

Wear safety glasses or goggles.

V Volts Direct Current

A Amperes n

No-Load Speed

Hz Hertz Class II Construction

W Watts

Earthing Terminal

min minutes

Safety Alert Symbol

Alternating

Current

/min.

Revolutions or

Reciprocation per

minute

edge of wheel has been rounded off, you are free to operate the

grinder in either the A or B direction.

Starting and stopping (Fig A)

WARNING: Before using the tool, check whether the

handle is tightened securely. Check whether the switch is

working normally.

Before plugging in the tool to the power supply, check whether the

switch is in the OFF position.

WARNING: Do not switch the tool on or off while under

load conditions.

Proper hand position (Fig G)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side handle (ﬁgure A),

with the other hand on the body of the tool, as shown in ﬁgure G.

Switch

CAUTION: Hold the body of the tool ﬁrmly to maintain control of the

tool at start up and during use and until the wheel or accessory stops

rotating. Make sure the wheel has come to a complete stop be fore

laying the tool down.

NOTE: To reduce unexpected tool movement, do not switch the tool

on or off while under load conditions. Allow the grinder to run up to

full speed before touching the work surface. Lift the tool from the

surface before turning the tool off. Allow the tool to stop rotating

before putting it down.

WARNING: Before connecting the tool to a power supply,

be sure the slider switch is in the off position by pressing

the front part of the switch and releasing. Ensure the

slider switch is in the off position as described above after

any interruption in power supply to the tool, such as the

activation of a ground fault interrupter, throwing of a

circuit breaker, accidental unplugging, or power failure. If

the slider switch is locked on when the power is

connected, the tool will start unexpectedly.

Lock-On feature of the switch

Press the trigger (1), the tool will start. Keep pressing the trigger,

then slide trigger (1) to the front of the tool, the unit will be locked into

“on“ position. To turn off the tool, press the trigger (1) then loose, the

tool will stop running.

Explanation: Before coming into contact with the object you

are working on, make sure the abrasive wheel is turning at

maximum speed. Before turning off the tool, lift the tool up

from the object you are working on.

CAUTION: Make sure the abrasive wheel is completely

stopped before putting down the tool.

(Original instructions) ENGLISH

5. Press the spindle lock (2) and rotate the spindle (6) until it locks

in position (Fig. C2).

6. Tighten the ﬂange (9) with the two-pin spanner supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the ﬂange (9) with the two-pin

spanner.

WARNING: Do not use a damaged disc.

Attaching the Side Handle (Fig D)

WARNING: Before using the tool, check that the handle

is tightened securely.

WARNING: The side handle should always be used to

maintain control of the tool at all times.

Screw the side handle (4) tightly into one of the holes (10) or (11) on

either side of the gear case.

Preparation before use

• Attach the safety guard and appropriate abrasive or grinding

wheels. Do not use abrasive or grinding wheels that are overly

worn.

• Make sure that the inner and outer ﬂanges are attached

correctly.

• Make sure that the abrasive or grinding wheels are rotating in the

direction of the arrows on the accessories and tool.

VOLTAGE DROPS

In rush currents cause short-time voltage drops. Under unfavourable

power supply conditions, other equipment may be affected. If the

system impedance of the power supply is lower than 0.175Ω ,

disturbances are unlikely to occur.

USE (Fig F)

WARNING: Always observe the safety instructions and

applicable regulations.

WARNING: To minimize the danger of serious

personal injury, please switch off the tool power and

disconnect all plugs before adjusting or

removing/installing any accessory. Before

reassembling the tool, press and release the trigger

switch to make sure the tool is already switched off.

• Make sure all materials to be grinded are secured in position.

• Apply slight pressure to the tool. Do not apply side pressure to

the abrasive disc.

• Avoid overloading. If the tool becomes hot, let it spin for a few

minutes with no load.

1. Be sure to hold the tool tightly with both hands (one hand on

housing, the other on side handle). Start the tool and bring the

grinding wheel on the workpiece.

2. Keep the edge of the wheel tilted at angle from 15 to 30 degrees

against the surface of the workpiece.

3. When using a new grinding wheel, do not operate the wheel in

the B direction, otherwise, it will cut into the workpiece. When the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STGL2223 in the language / languages: English, French as an attachment in your email.

The manual is 8,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley STGL2223 Manual

Product: