720428
5
Zoom out
Zoom in
Previous page
1/10
Next page
5
ENGLISH
(Original instructions)
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised STANLEY Service Centre
in order to avoid a hazard.
Using an extension cable
Always use an approved extension cable suitable for the
power input of this tool (see technical data). Before use,
inspect the extension cable for signs of damage, wear
and ageing. Replace the extension cable if damaged or
defective. When using a cable reel, always unwind the
cable completely. Use of an extension cable not suitable
for the power input of the tool or which is damaged or
defective may result in a risk of fire and electric shock.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Chuck
5. Sleeve
6. Bit Shaft
7. Speed dial
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Inserting and removing bits (fig. A, B)
Open the chuck by turning the sleeve (5) counter-
clockwise and insert the bit shank.
Place the bit shaft (6) in the chuck as far as it will go and
lift slightly before tightening.
Tighten firmly by turning the sleeve clockwise.
To remove the bit shaft (6), proceed in reverse order.
Removing and fitting the chuck(fig. C, D)
Open the chuck jaws as far as possible.
Insert a screwdriver into the chuck and remove the
chuck retaining screw by turning clockwise as shown in
figure C.
Tighten an hex key into the chuck and strike it with a
hammer as shown in figure D. This will loosen the chuck
so that it can be unscrewed by hand.
To refit the chuck, proceed in reverse order.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Selecting the direction of rotation (fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
slider (3) to the left position.
To select reverse rotation, push the forward/reverse
slider to the right.
Viewed when holding the drill in the operating position. After
any reversing operations, return slider (3) to forward
position.
Warning! Never change the direction of rotation while the
motor is running.
Switching on and off
To switch the tool on, press the variable speed switch
(1). The tool speed depends on how far you press the
switch.
For continuous operation, press the lock-on button (2)
and release the variable speed switch. This option is
available only at full speed.
To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Based on the different applications, turn around the
speed dial (7) to control the maximum speed.
Proper Hand Position (fig.F)
Warning! To reduce the risk of serious personal
injury, ALWAYS use proper hand position as
shown in figure F.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STDR5510C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STDR5510C in the language / languages: English as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info